Bedienungsanleitung Worcester-Bosch GB162-80 (Seite 30 von 72) (Englisch)

697434

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Installation

6720813171 (2016/05)30

Connection to the terminal strip of the boiler

▶ Connect the external pump, if available, (not the pump of the pump

group) to the green PK terminal. The maximum allowed connected

load of the pump = 250 Watts.

Fig. 56 Terminal strip - external heating pump 230 V (connection

colour green)

Connecting the DHW pump

▶ Connect the DHW pump to the grey PS terminal.

The maximum allowed connected load of the pump = 250 Watts.

Fig. 57 Terminal strip - DHW pump 230V (connection colour grey)

Connecting the DHW circulation pump

▶ Connect the DHW circulation pump to the lilac PZ terminal. The

maximum allowed connected load of the pump = 250 Watts.

Fig. 58 Terminal strip - DHW pump 230 V (connection colour grey)

Connecting to the mains

A mains supply of 230 V - 50 Hz is required.

External controls are suitable for volt free installation.

Wiring to the boiler must be in accordance with the current I.E.E.

(BS 7671) Wiring Regulations and any local regulations.

Wiring should be a 3 core PVC insulated cable, not less than 0.75 mm²

(24 x 0.2 mm), and to table 16 of BS 6500.

Connection must be made in a way that allows complete isolation of the

electrical supply such as a double pole switch having 3 mm contact

separation in both poles, or by a three pin connector, serving only the

boiler and system controls. This boiler is equipped with a double pole

switch [1]. The means of isolation must be accessible to the user after

installation.

The electrical connection to the mains supply should be readily

accessible and adjacent to the boiler.

If the supply cord is damaged, it must be replaced by a registered Gas

Safe installer to avoid a hazard and must be an original spare part.

The electrical supply for both the boiler and the system must be taken

from the same fused spur outlet.

Fig. 59 Mains supply

8.5.6 Installing function modules (accessories)

The following function modules (accessories) can be connected to the

boiler:

• Heat demand 0-10 V module EM10

• Error reporting module EM10

• Switch module WM10

• Mixing module MM10

• Solar module SM10.

Function modules (accessories) can be installed in 2 ways:

• in the boiler (max. 2)

• outside the boiler.

Both methods are described below.

▶ Determine how the modules have to be installed.

Installing and connecting function modules (accessories) in the

boiler

▶ Loosen the screw [1].

▶ Pull open the draw [2].

Fig. 60 Opening the draw

All Worcester boilers require a permanent live.

DANGER: Danger of fatal accident due to electric shock.

▶ Disconnect the boiler from the mains power supply

before working on the boiler.

6 720 648 726-056.1TD

6 720 648 726-057.1TD

6 720 648 726-058.1TD

Refer to the installation instructions of the relevant

function modules for information about installation and

combination possibilities.

OFF

6 720 648 726-059.1TD

6 720 648 726-060.1TD

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worcester-Bosch GB162-80 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Worcester-Bosch GB162-80

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info