Bedienungsanleitung Worcester-Bosch Greenstar 8000 Life Regular

809242

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Operating the appliance

Greenstar 8000 Life – 6720883873 (2021/05)

3.3 Topping up the system pressure

External filling loop

Once the external filling loop and the external pressure gauge have been

located, follow the instructions for re-pressurising the system.

▶ Unscrew the blanking cap [1].

▶ Attach the hose [2] to the valve.

– Usually one end of the hose is already connected to one of the

system fill isolation valves.

▶ Ensure both ends [3] of the hose are screwed on hand tight.

▶ Monitor the pressure via the external pressure gauge.

– The system fill isolation valves [4] are in a closed position (the

handle/screwdriver slot is across the valve).

▶ Turn the handle/screwdriver slot through 90° to open valves and

slowly fill the system.

– The system fill isolation valves [5] are opened (the handle/

screwdriver slot is in-line with the valve).

– The pressure at the display will start to rise.

▶ Set the pressure between 1 and 1.5 bar pressure.

▶ Turn the handles/screwdriver slots back, through 90°, to close the

valves.

– The system fill isolation valves [6] are in a closed position (the

handle/screwdriver slot is across the valve).

▶ Top up the system pressure, if as a result of the air bleeding the

pressure drops off.

Once the pressure has settled between 1 and 1.5 bar.

▶ Ensure the valves are closed.

▶ Remove the hose [2] and replace the blanking cap [1].

Fig. 2

If the pressure reads more than 1.5 bar as a result of over filling:

▶ Bleed one radiator until the pressure gauge returns to between 1 and

1.5 bar.

4 Operating the appliance

4.1 Control panel overview

Fig. 3 Control panel

[1] Display

[2]  and  keys: To navigate through menus and increase/decrease

settings

[3] d key: Return/back

[4] ok key: Save settings, Chimney sweeper key (Service Engineer

function): press 5 seconds for chimney sweeper mode

[5] eco key: Hot water preheat selection (not applicable for regular

appliances)

[6] Hot water key: Adjusting the hot water temperature (not

applicable for regular appliances)

[7] Heating key: Heating mode on, set the maximum flow

temperature

4.2 Symbols in the display

Table 3 Symbols in the display

0010026889-001

Symbol Explanation

Central heating ON

Is displayed with the appliance status code and diagnostic

code during a fault condition

Burner ON/OFF

Connection with the Wi-Fi network (only available with

accessories)

Connection with RF transmitter, e.g. Comfort+ II RF room

thermostat (only available with Key accessories)

chimney sweep mode

Service mode

Eco-Mode (not applicable for regular appliances)

Hot water ON (not applicable for regular appliances)

0010021505-001

reset

eco

5 sec

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worcester-Bosch Greenstar 8000 Life Regular - GR8300iW Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info