809292
12
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
12
Controls
Greenstar i ErP – 6 720 806 946 (2015/03)
These are not faults, but provide information concerning the current status of the appliance.
During normal appliance operation various Status codes can be displayed by pressing the button.
The first screen of the Information menu displays the current Status code, this will change as the appliance runs through the various
modes and sequences.
3.1.2 Basic adjust mode
Status code Description
200 Central heating system is being heated.
201 Domestic hot water system is being heated.
202 Anti rapid cycle mode.
The boiler has commenced anti-cycle period for CH. Can be adjusted in boiler settings (2.3b).
Default 5 Minutes
203 System stand by
The appliance is waiting for the heating system to cool.
204 System waiting.
208 Appliance in service Test mode (Min/Max)
265 EMS intelligent controller has forced stan-by-mode due to low heating load.
The appliance is compensating for the power required from the EMS room controller is less than the
minimum output of the boiler).
268 Component test mode.
Appliance is running the manual component test as activated in the menus.
270 Power up mode.
(appliance is powering up).
283 Burner starting.
The boiler prepares for a burner start. The fan and the pump are being controlled.
284 Gas valve(s) opened, flame must be detected within safety time.
The boiler prepares for a burner start. The gas valve is being controlled.
305 Anti fast cycle mode (domestic hot water keep warm function).
Diverter valve is held in hot water position for a period of time (determined by the software) after hot
water demand
309 Central heating and domestic hot water system are being heated.
357 Appliance in air purge mode.
Primary heat exchanger air venting program active - approximately 100 seconds.
358 Three way valve kick.
If the 3-way valve hasn't moved in within 48 hours, the valve will operate once to prevent seizure.
Table 5 Operational status codes
If you see basic adjust mode in the home screen when attempting to make temperature adjustments, the
appliance has been optimised for your heating system and should not need adjustment.
Please use your room thermostat to adjust your heating temperature if you still cannot achieve the desired room
temperature the Installation, Commissioning and Servicing Instructions contain details on how to disable the
basic adjust mode; this will allow further adjustment of the appliances settings.
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Worcester-Bosch Greenstar i wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info