Bedienungsanleitung Worcester-Bosch Greenstar Sense ll (Seite 18 von 48) (Englisch)

809350

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Working with the main menu

Sense ll – 6 720 812 775 (2014/10)

5.2 Heat source settings

This menu is only available for certain types of heat source if the

system is designed and configured accordingly (e.g. in systems

without cascade module).

Menu: Heat appliance

5.3 Adapting settings for heating system

automatic mode

Normally, the time program provides the best heating comfort.

In the default settings for each heating circuit, time program 1

is active with the following settings:

• Starting at 06:00 (08:00 on Saturdays and Sundays) heat

to 21 °C (heating mode). Starting at 23:00 heat to 15 °C

(setback mode).

These settings provide economic heating from 23:00 in the

evening until 06:00 in the morning on the following day.

Heating circuit 1-4

If more than one heating circuit has been installed and

configured, the settings for heating circuits 1-4 are changed in

the same way as for systems with one heating circuit. However,

changes are valid only for the selected heating circuit.

Assigning unique names to heating circuits makes it much

easier to make the right selection.

A Sense I remote control can be installed for each heating

circuit. At the Sense I, the required room temperature can be

temporarily changed until the next switching point of the time

program. After this, the Sense ll regains control until the setting

at the Sense I is changed again.

Menu: Heating

Menu item description

Activate

emergency

operation /

Deactivate

emergency

operation

In emergency operation heating and

DHW heating are active.

Emerg. op. flow

temp.

Set flow temperature in emergency

operation

Heating Switch the heating system on and off.

Heating max.

temperature

Maximum flow temperature for

heating system

DHW Switch DHW heating on and off.

DHW max. temp. Maximum domestic DHW temperature

Table 12 Heat source settings

Menu item description

Temperature

settings/

Setback

threshold

If the time program with 2 temperature

levels is active, the temperatures for the

2 levels Heating and Setback can be set

in this menu.

If the time program with Freely

adjustable temperature is active, the

setback threshold is set here. This is the

temperature above which the setback

mode is activates.

( Tab. 14, page 19)

Time program  Chapter 5.3.2, page 19

Start opt. time

prog.

 Chapter 5.3.3, page 25

Sum./wint.

changeover

 Chapter 5.3.4, page 25

Operating Mode Only available if the control type Constant

is set for the selected heating circuit

( Chapter 5.3.1, page 19).

Rename heating

circuit

The name of the selected heating circuit

can be customised here (only available if

more than one heating circuit is

installed). This helps to select the correct

heating circuit, e.g. “underfloor heating

system” or “attic apartment”. The names

are set by default to Heating circuit 1-4

( Tab. 18, page 23).

Table 13 Settings for heating system automatic mode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worcester-Bosch Greenstar Sense ll Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info