Bedienungsanleitung Worcester-Bosch Greenstyle Bewdley (Seite 24 von 36) (Englisch)

809294

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

WOOD HEATING

Controlled combustion is the most efcient technique for wood

heating because it enables you to select the type of combustion you

want for each given situation. The wood will burn slowly if the wood

stove air intake control is adjusted to reduce the oxygen supply

in the combustion chamber to a minimum. On the other hand,

wood will burn quickly if the air control is adjusted to admit a larger

quantity of oxygen in the combustion chamber. When the stove is

operating at the desired temperature close the primary air control

and use the airwash to control the burn rate. Refer to the primary

air settings table for operation setting. Real operating conditions

may give very different results than those obtained during testing

according to the species of wood used, its moisture content, the

size and density of the pieces, the length of the chimney, altitude

and outside temperature.

RELOADING

Once you have obtained a good bed of embers, you should reload

the unit. In order to do so, open the air controls to maximum a

few seconds prior to opening the stove’s door. Then proceed by

opening the door very slowly; open it one or two inches for 5 to

10 seconds, before opening it completely to increase the draught

and thus eliminate the smoke which is stagnant in a state of slow

combustion in the stove. Then bring the red embers to the front of

the stove and reload the unit.

For optimal operation of your stove , we recommend you to operate

it with a wood load approximately equivalent to the height of re

bricks. Do not stack wood higher than the rebrick.

It is important to note that wood combustion consumes ambient

oxygen in the room.

CREOSOTE - FORMATION AND NEED FOR REMOVAL

When wood is burned slowly, it produces tar and other organic

vapors, which combine with expelled moisture to form creosote.

The creosote vapours condense in the relatively cool chimney ue

of a slow-burning re. As a result, creosote residue accumulates

on the ue lining. When ignited this creosote makes an extremely

hot re. The chimney connector and chimney should be inspected

at least once every two months during the heating season to

determine if a creosote build-up has occurred.

We strongly recommend that you install a magnetic thermometer on

your smoke exhaust pipe, approximately 457mm above the stove.

This thermometer will indicate the temperature of your gas exhaust

fumes within the smoke exhaust system. The ideal temperature

for these gases is somewhere between 123°C and 270°C. Below

these temperatures, the build-up of creosote is promoted. Above

300°C, heat is wasted since a too large quantity is lost into the

atmosphere.

REFUELING

If there is insufcient burning material in the re bed to light a new

wood log, excessive smoke emission can occur. Refueling must

be carried out onto a sufcient quality of glowing embers and ash

approximately 25 mm deep. Evenly distribute the embers over the

rebed and open the airwash control fully. The new fuel charge will

ignite in a reasonable period of time. If there are too few embers in

the re bed, add suitable kindling to prevent excessive smoke. Do

not let the re diminish too far before refueling. Open the door and

add fuel (taking care not to overll). Close the door but leave the

primary and secondary air supply fully open for a few minutes until

a bright re is achieved. The primary air should be closed and the

secondary air adjusted as necessary. You will nd that a wood log

of approximately 2.5kg will produce a clean burning re for about

1 hour .

MULTI-FUEL (BEWDLEY 3 & BEWDLEY 5 ONLY)

Start your re as you normally would as instructed in the “IGNITION”

section of this manual. Allow the re to become well established

before adding the ‘Defra-authorised’ smokeless fuel (as published

on the Defra website (https://smokecontrol.defra.gov.uk/fuels.php).

1. Open the Primary Air Control fully to establish a glowing bed

before adding your smokeless fuel.

The secondary air slide is located above the viewing glass. (The lower air slide below the glass is primary and is only used for

start up air and should not be left open for more than 5 minutes after starting your re.) Sliding secondary air slide to the far

right position is fully open position. Your stove is tested for use in smoke controlled areas if operated in accordance with the

instructions below.

Burn Rate Adjust secondary air slide from full high position

Low Fully slid to the left hand stop

Medium Bewdley 3 Bewdley 5 Bewdley 8

16mm from fully open position 15mm from fully open position 30mm from fully open position

High Fully slid to the right

WARNING: Never alter the damper slide or

the adjustment range to increase ring for

any reason. Doing so could result in stove

damage and will void your warranty.

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

WARNING:

• Never over re your stove. If any part of

the stove starts to glow red, over ring is

happening. Readjust the air intake control

at a lower setting.

• The installation of a log cradle or grates

is not recommended in your stove . Never

put wood above the rebrick lining of the

rebox.

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

USER INSTRUCTION

CONTROLLING YOUR STOVE

Bewdley 3 Bewdley 5 Bewdley 8

Approximate size of

wooden log 0.9kg 1.1kg 2.5kg

Approximate clean

burn time 45 min. 50 min. 1 hour

24 6720818040 C 11/2017

Worcester-Bosch Greenstyle Bewdley Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info