Bedienungsanleitung Worcester Greenstore Ground Source (Seite 24 von 28) (Englisch)

809329

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENERGY SAVINGS

6 720 802 172 (2012/06)24

15 ENERGY SAVINGS

INSPECTION AND MAINTENANCE

To achieve as low energy consumption as possible for a longer period of

time, we recommend that you have an annual service and any

maintenance carried out by a competent person.

UNDERFLOOR HEATING

Do not set a flow temperature that is higher than the highest value

recommended by the floor manufacturer.

AIRING

Do not leave the windows ajar when you air. This makes heat leave the

room all the time, but the air quality in the room does not improve.

Instead, open the windows fully for a short time.

ADDITIONAL ELECTRIC HEAT

Different settings (e.g. extra hot water) lead to the activation of an

additional electric heat source and thereby to higher energy

consumption.

Always select a temperature setting for hot water and heating that is as

low as possible.

16 MAINTENANCE

The heat pump requires minimal upkeep. Some inspection is

recommended nevertheless for the heat pump to perform as well as

possible. Check the following points a couple of times during the first

year. Subsequently they should be checked occasionally during the

year:

• Safety valves

• Expansion vessel (plastic vessel collector circuit)

• Particle filter

16.1 CHECKING THE SAFETY VALVES

▶ Check that the waste water hose from the safety valve is not blocked.

16.2 EXPANSION VESSEL

A plastic expansion vessel is connected to the heat pump collector

circuit ("the cold side"). The level in the vessel must not be less than

minimum level 1/3. If the fluid level is too low, contact your installer.

16.3 PARTICLE FILTER

The particle filter (dirt filter) ensures that no particles or dirt get into the

heat exchangers. In time, the filter can become clogged and must be

cleaned. There are particle filters on both the "hot and cold sides". The

particle filter should be cleaned as follows:

▶ Switch off the heat pump with the ON/OFF button.

▶ Shut the valve and screw off the sealing lid.

▶ Release the locking ring which holds the sieve in the valve. Use the

accompanying locking ring bar. (Image 32)

▶ Lift the sieve out from the valve and rinse it clean with water.

▶ Replace the sieve, the locking ring and the sealing lid.

▶ Open the valve and start the heat pump with the ON/OFF button.

Fig. 32

17 THE GUARANTEE

The Greenstore Liquid to Water heat pump has a 2 year guarantee

against faulty material or manufacture subject to Terms and conditions.

To read the full Terms and Conditions please visit us online at

www.worcester-bosch.co.uk/guarantee. The Guarantee Registration

form is available on this same page and can be completed and submitted

electronically. Alternatively please telephone one of our Guarantee

Registration advisors on 0844 892 2552. Your statutory rights are not

affected by the manufacturers guarantee.

The safety valve should be checked by a qualified

engineer - usually as part of an annual service visit.

Never close the safety valve or obstruct it’s discharge

pipe.

6 720 613 623-05.1R

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worcester Greenstore Ground Source Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info