Bedienungsanleitung Workzone 2024001 (Seite 12 von 16) (Englisch)

724625

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

24V Lithium-ion Cordless Drill with Hammer Action

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. 2024001 • 02/2019 • 63524

(toll free)

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

24V Lithium-ion Cordless Drill with Hammer Action

MODEL: №.2024001 • 02/2019 • 63524

20 21

Drill/driver Overload

This drill/driver is tted with an overload protection. If the drill/driver is

excessively forced, or the task being performed is too great for the drill/

driver, the drill/driver will automatically go into an overload mode. When

the drill/driver goes into overload, the drill/driver will automatically and

suddenly STOP. To reset the overload, simply release the trigger. When the

trigger is pressed again, the drill/driver will restart. Resume work after the

overload has been reset, but reduce the load by using a smaller drill/driver

bit or re-sharpen the existing drill/driver bit and reduce the amount of force

placed on the drill/driver. If the drill/driver is set to High speed on the gear

selector, consider changing to low speed selection.

CAUTION. Do not continue to overload the drill/driver and constantly reset

the overload. Doing this will cause the battery cells to over heat.

Temperature cut out

If the drill/driver is constantly overloaded, or the drill/driver is used

constantly at maximum rating in high ambient conditions, the battery cells

may overheat causing the battery pack to shut down.

When this occurs you will need to allow the battery cells to cool.

NOTE: The drill/driver will not restart until the battery pack has cooled.

To reduce the temperature of the cells remove the battery pack from the

drill/driver and place the battery pack in a free air environment, out of direct

sunlight or any other heat source.

DO NOT force cool the pack in any way. Do not place in refrigerators or

freezers.

When the battery pack has cooled down it can again be used to operate

the drill/driver, as long as the load or the conditions causing the original

excessive temperature has been corrected.

Low voltage cut out

The battery pack used on this tool is tted with a low voltage cut out feature

within the circuitry.

The low voltage cut out feature operates when the voltage drops below a

preset value. This feature automatically stops the drill/driver from operating

(similar to that of the overload condition). When this condition occurs you

will need to either insert another battery into the drill/driver or recharge the

existing battery.

The low voltage cut out feature has been added to maximise the life of the

battery cells in the battery (9). When this occurs, recharge the battery pack

by following the battery charging section in this manual.

NOTE: Attempting to restart the tool without either recharging the battery

or installing another battery (with charge) will lead to drill/driver restarting

and then stopping again, after only a few seconds of operation.

Drill/driving

Drill/driving metals

• Always clamp sheet metal.

• Support thin metal with a block of wood to avoid distorting it.

• Use a punch to mark the centre of the hole.

• Use a suitable lubricant for the material you are working on,

USE: FOR:

Oil Steel

Turpentine or paran Aluminium

Do not lubricate Brass, copper or cast iron

Do not Lubricate Concrete based material

Drill/driving plastics and plastic coated chipboard

• Use high speed drill/driver bits

• See drill/driving wood below

Drill/driving wood

• Clamp a piece of scrap wood to the back of your work to prevent

splintering.

Hammer drill operations.

• Where possible, use High speed.

• Select the hammer position on the function selection collar (3).

• Use drill bits specically for masonary applications.

• Ensure to wear safety glasses.

Drill / driver Overload Drill / driving

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone 2024001 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info