Bedienungsanleitung Workzone CS20V (Seite 8 von 19) (Englisch)

724628

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

AFTER SALES SUPPORT e-mail: info.aldi@positecgroup.com

1300 889 028 (toll free) MODEL No.: CS20V • 63350 • 01/2019

AFTER SALES SUPPORT e-mail: info.aldi@positecgroup.com

1300 889 028 (toll free) MODEL No.: CS20V • 63350 • 01/2019

14 15

e. Do not use dull or damaged blades. Unsharpened or improperly set

blades produce narrow kerf causing excessive friction, blade binding and

kickback.

f. Blade depth and bevel adjusting locking levers must be tight and

secure before making cut. If blade adjustment shifts while cutting, it

may cause binding and kickback.

Use extra caution when sawing into existing walls or other blind areas.

The protruding blade may cut objects that can cause kickback.

a. Check lower guard for proper closing before each use. Do not operate the

saw if lower guard does not move freely and close instantly. Never clamp or tie

the lower guard into the open position. If saw is accidentally dropped, lower

guard may be bent. Raise the lower guard with the retracting handle and make

sure it moves freely and does not touch the blade or any other part, in all angles

and depths of cut.

b. Check the operation of the lower guard spring. If the guard and the spring

are not operating properly, they must be serviced before use. Lower guard may

operate sluggishly due to damaged parts, gummy deposits, or a build-up of

debris.

c. Lower guard should be retracted manually only for special cuts such as

“plunge cuts” and “compound cuts.” Raise lower guard by retracting handle

and as soon as blade enters the material, the lower guard must be released.

For all other sawing, the lower guard should operate automatically.

d. Always observe that the lower guard is covering the blade before placing

An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in its path. Be aware of the time it

takes for the blade to stop after switch is released.

e. Do not use abrasive wheels.

Wear eye protection

Wear ear protection

Wear breathing protection

d. Support large panels to minimise the risk of blade pinching and

kickback. Large panels tend to sag under their own weight. Supports

must be placed under the panel on both sides, near the line of cut and

near the edge of the panel.

arms to resist kickback forces. Position your body to either side of the

blade, but not in line with the blade. Kickback could cause the saw to

jump backwards, but kickback forces can be controlled by the operator,

if proper precautions are taken.

b. When blade is binding, or when interrupting a cut for any reason,

release the trigger and hold the saw motionless in the material until

the blade comes to a complete stop. Never attempt to remove the saw

from the work or pull the saw backward while the blade is in motion or

kickback may occur. Investigate and take corrective actions to eliminate

the cause of blade binding.

c. When restarting a saw in the workpiece, centre the saw blade in the

kerf so that the saw teeth are not engaged into the material.

If a saw blade is binds, it may walk up or kickback from the workpiece as

the saw is restarted.

Causes and operator prevention of kickback:

• Kickback is a sudden reaction to a pinched, bound or misaligned saw

blade, causing an uncontrolled saw to lift up and out of the workpiece

toward the operator.

• When the blade is pinched or bound tightly by the kerf closing down, the

blade stalls and the motor reaction drives the unit rapidly back toward the

operator.

• If the blade becomes twisted or misaligned in the cut, the teeth at the

back edge of the blade can dig into the top surface of the wood causing

the blade to climb out of the kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect operating procedures

or conditions and can be avoided by taking proper precautions as given

below.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone CS20V Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info