Bedienungsanleitung Workzone INF3800A (Seite 15 von 22) (Englisch)

724653

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

3600W Digital Inverter with Pure Sine Wave

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL: №. INF3800A-1 • 03/2018 • 59905

(toll free)

AFTER SALES SUPPORT

(toll free)

3600W Digital Inverter with Pure Sine Wave

e-mail: help@powertoolsupport.com1800 909 909

MODEL: №. INF3800A-1 • 03/2018 • 59905

26 27

You may now move one or both of these switches to the UP “ON” position

depending on how many appliances you are using. A reminder here that

the generator will only power a product or combination of products up to

a maximum of 3400W continually and a little higher 3600W at startup

(Fig Y).

9. As you turn on the appliances and use them it will generate load on the

generator and the engine speed uctuate as requirements from the

appliances increases and decreases. This is normal. 

WARNING: All appliances are rated dierently. This generator will work

only with Australian approved rated appliances with an input voltage of

220-240Va.c (Fig Z). Check your appliances meet this requirement on its

rating label before using them. In simple terms if you cant use the product

in your home you denitely cannot use it on this generator.

Overload condition ( Where the appliances want more

power then the generator can provide)

Once operating, If the AC side of the generator becomes overloaded , the

red load status indicator (8) LED will illuminate. The generator will continue

to supply 240Va.c output for a very short time, but if the load is not reduced,

the 240V supply will be automatically shut down. To reduce load rstly you

can stop using one appliance and turn it o , see if that recties the problem.

If not refer to page 14 on loading’s and how they work. If this does NOT solve

your problem, you will need to reset an overload condition and shut down

the engine of the generator, howeverENSURE to follow the procedure and

thus restart the engine after the load being applied to the generator has

been reduced. Always connect the largest appliance you want to run rst

allowing it time to draw current to start . After 20-30 seconds connect the

second appliance.

Normal procedure for Stopping the Engine

(Full shut down and Store)

1.  Turn “OFF” the 240Va.c Outlet Power On/O switches (1 & 2) (Fig R).

2. Remove any appliances connected to either of the 3 outlets (Fig Q).

3. Allow the engine to slow down and idle for approx 15-30 seconds.

4. Press the engine On/O switch (4) to the “OFF” position as indicated

by an “O” (Fig. U). The unit will stop running .

5.  Turn the fuel lever / tap (26) anti clockwise to the “OFF” position (Fig. AA)

Overload procedure for restarting and resetting the engine

1. Turn “OFF” the 240Va.c Outlet Power On/O switches (1 & 2) (Fig R).

2. Allow the engine to slow down and idle for approximately

15-30 seconds.

3. Press the engine On/O switch (4) to the “OFF” position as indicated by an

“O”(Fig. AB). The unit will stop running and is shut down. Now follow the

normal starting procedure to restart the generator.

AB.

AA.

OFF

Operation Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone INF3800A Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info