Bedienungsanleitung Workzone IW36 (Seite 13 von 18) (Englisch)

724651

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

AFTER SALES SUPPORTe-mail: help@powertoolsupport.com

1800 909 909 (toll free)MODEL No.: IW36 • 61551 • 07/2018

AFTER SALES SUPPORTe-mail: help@powertoolsupport.com

1800 909 909 (toll free)MODEL No.: IW36 • 61551 • 07/2018

24 25

Impact Wrench Safety Features

Impact Wrench Overload

This Impact Wrench is tted with an overload protection. If the Impact

Wrench is excessively forced, or the task being performed is too great

for the Impact Wrench , the Impact Wrench will automatically go into an

overload mode. When the Impact Wrench goes into overload, the Impact

Wrench will automatically and suddenly STOP. To reset the overload,

simply release the trigger switch (5). When the trigger is pressed again,

the Impact Wrench will restart. Resume work after the overload has been

reset, but reduce the load by using a smaller Impact Wrench bit or

CAUTION: Do not continue to overload the Impact Wrench and constantly

reset the overload. Doing this will cause the battery cells to over heat.

Temperature cut out

If the Impact Wrench is constantly overloaded, or the Impact Wrench

is used constantly at maximum rating in high ambient conditions, the

battery cells may overheat causing the battery pack to shut down.

When this occurs you will need to allow the battery cells to cool.

NOTE: The Impact Wrench will not restart until the battery pack has

cooled.

To reduce the temperature of the cells remove the battery pack from the

Impact Wrench and place the battery pack in a free air environment, out of

direct sunlight or any other heat source.

DO NOT force cool the pack in any way. Do not place in refrigerators or

freezers.

When the battery pack has cooled down it can again be used to operate

the Impact Wrench, as long as the load or the conditions causing the

original excessive temperature has been corrected.

Low voltage cut out

This Impact Wrench is tted with a low voltage cut out feature.

The low voltage cut out feature operates when the voltage drops below

a preset value. This feature automatically stops the Impact Wrench from

operating (similar to that of the overload condition). When this condition

occurs you will need to either insert another battery into the Impact

Wrench or recharge the existing battery.

The low voltage cut out feature has been added to maximise the life of the

battery cells. When this occurs, recharge the battery pack (6) by following

the battery charging section in this manual or the supplied manual from

your ALDI Xnity purchased charger.

NOTE: Attempting to restart the Impact Wrench without either recharging

the battery or installing another battery (with charge) will lead to Impact

Wrench restarting and then stopping again, after only a few seconds of

operation.

NOTE: For any issues related directly to your purchased ALDI Xnity

Battery / charger, contact the Customer Service of the manufacturer

as listed on the battery / charger packaging, manual or on the label

on the battery / charger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone IW36 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info