Bedienungsanleitung Workzone LCD699-2SC (Seite 10 von 16) (Englisch)

724656

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

12v Lithium-ion Cordless Drill with Hammer Action

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL No.: LCD699-2SC • 11/2017 • 54731

(toll free)

AFTER SALES SUPPORT

(toll free)

e-mail: help@powertoolsupport.com1800 909 909

12v Lithium-ion Cordless Drill with Hammer Action

MODEL No.: LCD699-2SC • 11/2017 • 54731

16 17

Using the drill/driver

Trigger switch

1. Use the forward/reverse switch (6) to select the

direction of rotation (Fig E), then pull the trigger

(8) (Fig F). This trigger switch is an electronic

variable speed control which enables the user to

vary the speed continuously.

The speed varies according to how far the

trigger switch is depressed.

The further it is depressed the faster the chuck

will rotate and the lighter it is depressed, the

slower it will rotate.

2. To stop the drill/driver, release the trigger

switch (8).

Note. The variable speed control tted to this

drill/driver is NOT intended to be used for long

periods of time during the operation of the task

being performed. Use the variable speed to

start drill/driving and screwing tasks, and then

fully depress the trigger once the task has started.

CAUTION. Extended use of the variable speed under load will overload and

then permanently damage the speed control.

Drill/driver Overload

This drill/driver is tted with an overload protection. If the drill/driver is

excessively forced, or the task being performed is too great for the drill/

driver, the drill/driver will automatically go into an overload mode. When

the drill/driver goes into overload, the drill/driver will automatically and

suddenly STOP. To reset the overload, simply release the trigger. When the

trigger is pressed again, the drill/driver will restart. Resume work after the

overload has been reset, but reduce the load by using a smaller drill/driver

bit or re-sharpen the existing drill/driver bit and reduce the amount of force

placed on the drill/driver. If the drill/driver is set to High speed on the gear

selector, consider changing to low speed selection.

CAUTION. Do not continue to overload the drill/driver and constantly reset

the overload. Doing this will cause the battery cells to over heat.

Temperature cut out

If the drill/driver is constantly overloaded, or the drill/driver is used

constantly at maximum rating in high ambient conditions, the battery cells

may overheat causing the battery pack to shut down.

When this occurs you will need to allow the battery cells to cool.

NOTE: The drill/driver will not restart until the battery pack has cooled.

To reduce the temperature of the cells remove the battery pack from the

drill/driver and place the battery pack in a free air environment, out of direct

sunlight or any other heat source.

DO NOT force cool the pack in any way. Do not place in refrigerators or

freezers.

When the battery pack has cooled down it can again be used to operate

the drill/driver, as long as the load or the conditions causing the original

excessive temperature has been corrected.

Low voltage cut out

The battery pack used on this tool is tted with a low voltage cut out feature

within the circuitry.

The low voltage cut out feature operates when the voltage drops below a

preset value. This feature automatically stops the drill/driver from operating

(similar to that of the overload condition). When this condition occurs you

will need to either insert another battery into the drill/driver or recharge the

existing battery.

The low voltage cut out feature has been added to maximise the life of the

battery cells in the battery (9). When this occurs, recharge the battery pack

by following the battery charging section in this manual.

NOTE: Attempting to restart the tool without either recharging the battery

or installing another battery (with charge) will lead to drill/driver restarting

and then stopping again, after only a few seconds of operation.

Forward/reverse switch

NOTE: You can only change the direction of rotation of the drill/driver using

the forward/reverse switch (6) when the trigger (8) is NOT depressed.

This switch will allow you to change the direction of the motor while the

trigger switch is not depressed.

Usig the Drill / Driver Temperature Cut out

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone LCD699-2SC Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info