Bedienungsanleitung Workzone S1B-DW01 (Seite 9 von 15) (Englisch)

724638

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

220W 3-in-1 Multi Purpose Sander

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL No.: S1B-DW01-220W • 09/2018 • 61865

(toll free)

AFTER SALES SUPPORT

(toll free)

220W 3-in-1 Multi Purpose Sander

e-mail: help@powertoolsupport.com1800 909 909

MODEL No.: S1B-DW01-220W • 09/2018 • 61865

14 15

Assembly Preparation

It is best to make a trial run on a scrap piece of material to determine the

optimum grades of sandpaper for a particular job. If there are still marks

on your work after sanding, try either going back to a coarser grade and

sanding the marks out before recommencing with the original choice of

grit, or try using a new piece of sandpaper to eliminate the unwanted marks

before going on to a ner grit and nishing the job.

Fitting / Attaching the sanding sheet

WARNING! Always remove the plug from the mains power socket

before carrying out any work on the sander.

NOTE: Before tting a new sanding sheet, remove any dust and dirt from the

sander plate.

Attaching sanding sheets using Velcro:

NOTE: Make sure the holes on the sandpaper are aligned with the holes on

the sander base plate. This ensures maximum dust removal and allows air

ow from the motor.

1. Attach the sanding sheet to the tted sander

plate by simply applying the underside of the

sandpaper onto the velcro base (Fig J). This

type of sandpaper is “hook and loop”, and the

velcro holds the sanding sheet in place.

2. To remove the sanding sheet, simply pull the

sanding sheet o the sander plate (Fig K).

Preparation

Fitting/changing the sander plates –

Random Orbital Sander Plate

WARNING! Always remove the plug from the mains power socket

before carrying out any work on the sander.

Changing from the tted rectangle sander plate (9) to the Random Orbital

Sander plate (13).

1. Using a philips head screwdriver (not supplied),

remove the four screws (12) visible on the

underside of the rectangle sander plate (9)

in an anti-clockwise direction (Fig A).

2. Once the 4 screws are all loose, remove the

pre-tted rectangle sander plate (9) (Fig B).

3. The random orbital sander plate (13) only

requires xing of the 4 x screws, and does not

require the rubber pins to be used.

4. Align the screw holes on the random orbital

sander plate (13) underside (non Velcro side),

with the threaded holes on the sander drive

plate (Fig H).

5. Using 4 x screw + washers from either of the

other sander plates (9) / (11), secure the random

orbital sander plate (13) onto the sander drive

plate by screwing in a clockwise direction (Fig I).

TIGHTEN

Selecting the suitable sanding sheet

The material removal rate and surface quality are determined by the grain

strength of the sandpaper. Ensure you use a suitable grit (g) of sandpaper

for working on dierent materials. The 80 grit (g) sandpaper supplied is

used for more coarse / rougher sanding / removal. The 240 grit (g) is better

suited for detail and ne sanding. This sander includes an 80g and 240g

sandpaper sheet for each sander plate base.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone S1B-DW01 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info