Bedienungsanleitung Worx WG169E.9 (Seite 14 von 148) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

576038

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

3-in-1 Grass Trimmer/Edger

or edging.

WARNING!

Only use 1.65mm

diameter cutting line. Other sizes of

line will not feed properly and will result

in improper cutting head function or can

cause serious injury. Do not use other

material such as wire, string, rope, etc.

Wire can break off during cutting and

become a dangerous projectile that can

cause serious injury.

EDGE /TRIMMING SUPPORT WHEELS

There are three optional positions for the Edge

/Trimming Support Wheels to attach when

assisting in Trimming and Edging.

Position 1: Using the guide wheels when

trimming in a forward or reverse direction

(See Fig. J1)

Position the Grass Trimmer in the trimming

position. Underneath the Safety Guard there is

a metal plate that the Edge/Trimming Support

Wheels will attach to. Slide the Support

Wheels horizontally onto the metal plate until

they lock into position so both the wheels are

facing in the forward direction (See Fig. B3).

The wheels should provide support when

you are trimming in the forward or reverse

direction.

Position 2: Using the guide wheels when

trimming Side to Side

Position the Grass Trimmer in the trimming

position. Underneath the Safety Guard there

is a metal plate that the Edge/Trimming

Support Wheels will attach to. Slide the

Support Wheels vertically onto the metal plate

until it locks into position (See Fig. B2). The

wheels should provide support when you are

trimming in a horizontal side to side direction

(See Fig. J2).

NOTE: you could also use the machine

without the guide wheels on guard when

trimming.

Position 3: Using the guide wheels when

edging (See Fig. I2)

WARNING: Make Sure the Safety

Switch is Locked Off to Prevent

Accidental Starting.

Change the tool from trimming into the

edging mode, the Edge /Trimming Support

Wheels (12) will attach on the side the trimmer

head as shown in Fig. B1.; rotate the main

handle as described in ‘’MAIN HANDLE

ROTATION’’, then unlock the Pivot Head

Locking Knob, and using adequate force, pull

the trimmer head into the desired position.

Make sure to adjust the trimmer head angle

to be in the lowest horizontal setting. Finally,

lock the Pivot Head Locking Knob (See Fig. H3)

and position the wheels on the ground for the

edging mode. While edging, keep the Flower

Guard/Edge Guide aligned with the sidewalk

edge, this will assist to edge in a straight path.

Only the tip of the line will make contact with

area being worked on. Do not force the line.

The edging wheels help protect the unit and

keep the unit from contacting the ground. Take

extra caution while edging, as objects can be

thrown from the trimmer line.

AUTOMATIC LINE FEED SYSTEM

When initially switching on the trimmer, a

small length of line is fed out. Each time the

tool is started from rest it will advance about

6.35mm of trimmer line.

A ‘clattering’ noise will be heard when the

lines hit the Line Cutter. DO NOT BE ALARMED

this is quite normal. After about 5 seconds

the line will be cut to the correct length and

the noise will reduce as the motor gains full

speed.

If the noise of the line being cut can’t be

heard, more line will need to be fed out.

To feed more line, it is ﬁrst necessary to allow

the trimmer to stop completely; it must come

to a complete rest, then restart, allowing the

motor to reach full speed.

Repeat above until you hear the line hitting

against the Line Cutter.

TO MANUALLY FEED THE LINE

(See Fig. K1)

Turn off the trimmer and remove the battery.

If required, line can be fed out manually.

To operate, press and release manual Line

Feed Button (17), while gently pulling out the

line until it is long enough to reach the Line

Cutter.

If the line extends past the Line Cutter, too

much line has been fed out.

If too much line is fed out, remove the Spool

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WG169E.9 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info