Bedienungsanleitung Worx WG629.1 (Seite 10 von 20) (Englisch, Französisch, Spanisch)

673107

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

20V Max Lithium Portable Power Cleaner

POSITEC Inc. has established

a partnership with the RBRC

Corporation to recycle any Positec

batteries with the RBRC-call2recycle

seal. For environmental protection,

please do not discard batteries in

the trash. After the batteries’ life

cycle is ended, then please call

1-800-822-8837 for a free service

that will properly dispose of the

battery.

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

ASSEMBLY & OPERATION

ACTION FIGURE

BEFORE OPERATION

Installing the battery pack See Fig. A1

Removing the battery pack See Fig. A2

Charging the battery pack

More details can be found in WA3742’s

manual

See Fig. A3

ASSEMBLY

NOTE: The power nozzle has two

working modes: short lance only

and short lance used together with

extension lance.

Working mode 1

Attaching short lance to the power

nozzle

NOTE: When attaching, align the

two projections on the lance with the

grooves of the power nozzle as shown

in Fig. B.

NOTE: In this working mode, the

highest pressure is 94psi. it is suitable

for light duty cleaning and watering.

See Fig. B

Attaching the Multi-spray nozzle

NOTE: When attaching, rotating the

nozzle left and right to make sure the

nozzle fully seated into position and

gently pulling it to make sure it is

locked into position securely.

See Fig. C

Working mode 2

Attaching extension lance to the power

nozzle

Attaching short lance to the extension

lance

NOTE: When attaching, align the

two projections on the lance with the

grooves of the power nozzle as shown

in Fig. D, E.

NOTE: In this working mode, the

highest pressure is 320psi. it is suitable

for removing strong stains.

See Fig.

D, E

Attaching the hose to the power nozzle

NOTE: After the hose is attached, check

the connection by gently pulling upon

the hose. It should not be pulled off.

See Fig.

F1, F2

Attaching your own water hose

(optional)

1. Remove the hose adaptor

2. Attach the home garden hose with

suitable connectors

NOTE: Except for the hose supplied,

you can also connect the power nozzle

to your own water hose with suitable

connectors.

NOTE: When retightening the quick

hose adapter, please tighten securely.

Otherwise, it may not draw any water

for proper operation.

See Fig.

G1, G2

OPERATION

Pressure setting

Your power nozzle has two pressure

modes.

See Fig. H

Start

NOTE: At the ﬁrst use, you need to

empty the air in hose, place the

power nozzle below waist level

(<5ft/1.5m), then attach the extension

lance and set it at high pressure. Do not

start working until the water

goes up along the hose and sprays out.

This could take up to 30

seconds or more depending on the

fresh water source.

See Fig. I

Selecting the nozzle pattern

NOTE: Choose a suitable nozzle

pattern according to your work. Spray

patterns 0

, 15

, 25

and 40

are

applicable for cleaning, and the spray

pattern with the symbol

is best

suitable for watering.

WARNING:

Do not shift the

nozzle pattern when the tool is

powered on.

See Fig. J

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WG629.1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info