Bedienungsanleitung Worx WG791E (Seite 12 von 144) (Deutsch, Englisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

578151

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

Lawn Mowing Robot EN

5. Software update

Your Landroid

M software can be updated when new versions

become available. You can check the software version installed on

your machine by pushing the ON/OFF button. The software version

will be displayed in the bottom right hand corner of the display.

The latest software can be downloaded from our website – see

below download and installation instructions;

Step 1: Locate the latest software version at : www.worxlandroid.com.

Copy the “.bin” file containing the latest software version to a USB

memory stick.

NOTE: Before transferring the “bin” file make sure the

memory stick does not contain other files or data.

Step 2: Remove the battery cover and insert the memory stick into

the USB port . (See Fig J1)

Step 3: Press the ON/OFF button for ten seconds until the mower

is powered ON. The new software version will be displayed in the

bottom right corner of the display. (See Fig J2)

Step 4: Remove the memory stick and refit the battery cover.

Step 5: After installing the new software you will need to reset the

diagnostic panel on your mower. Firstly, position the mower on a

horizontal surface.

Press Key “2” to enter the diagnosis interface, then press key

“5” for a few seconds until the three numbers 1 2 & 3 highlighted

below turn back to zero. (See Fig J3)

6. Maintenance

Your Landroid

M needs to be checked from time to time. The

Landroid

M works hard and after time needs a good cleaning as well

as having some parts replaced, as they can become worn.

In the following we want to let you know how to take care of your

Landroid

6.1 Keep it sharp

WARNING: Before cleaning, adjusting, or replacing

the Blades, turn your Landroid

M OFF by pressing

the ON/OFF Button to OFF and put on protective gloves.

WARNING: When fitting new blades, make sure

you replace ALL the blades. Always use new

screws when fitting blades . This is important to ensure

blade retention. Failure to use new screws could cause

serious injury.

The Landroid

M does not cut grass like other mowers. Its

Cutting Blades (14) are razor sharp on all 4 edges and spin in

both directions for maximum cutting capacity (See Fig. K ).Each

blade of your Landroid

M has 4 cutting edges. Depending on the

frequency the Landroid

M mows your lawn, the cutting blades will

need to be flipped/rotated periodically for a new cutting edge. If

your Landroid

M is programmed to mow the lawn every day then

the cutting blades will need to be rotated monthly for the best

mowing results. Each cutting blade will last up to 4 months when

it is programmed to mow every day. When the cutting blades are

dull and worn out, they should be replaced with the spare blades

provided with your Landroid

M. Spare blades are also available at

your nearest WORX retailer.

1 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WG791E Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Worx WG791E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info