Bedienungsanleitung Worx WR104 SI (Seite 12 von 20) (Englisch)

723920

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Owner’s Manual of Lawn Mowing Robot EN

7.2 Burying the Boundary Wire

If you are planning to bury the Boundary Wire, it is recommended to first peg it down. This allows you to easily change the layout

if necessary before burying the wire. When the boundary wire installation is complete, have Landroid

follow and check the path

by pressing

and . This will allow Landroid

to adjust to its new environment.

While observing Landroid

you can easily make alterations to the boundary wire to ensure the Landroid

's trouble-free tracking

when locating the charging station. Confirm that Landroid

docks in the charging station successfully, and bury the wire if desired.

7.3 Joining the boundary wire

If you want to extend and splice the boundary wire, use a connector. The connector is waterproof and provides optimal

connection.

Insert both wire ends in any two of the three holes of the connector. Insert the wires fully until both wire ends are visible

on the other side of the connector. (See Fig. J1) Press the connector together by using a pair of pliers. (See Fig. J2, J3)

WARNING! It is not recommended to simply splice the boundary wire with insulating tape or use a screw terminal

block for connection. A broken circuit may occur after a period of time as soil moisture can oxidize the wire.

8. Software update

The software can be updated when new versions become available.

The latest software can be downloaded from our website

www.worxlandroid.com. There are two methods to update software.

Method 1: Update via USB. See below for download and

installation instructions:

(1) Locate the latest software version at: www.worxlandroid.com.

Save the file to an empty FAT32 formatted USB (flash drive).

Delete any other files on the drive and check the format. If the

drive is not formatted in FAT32, please reformat the drive.

NOTE: the software update is downloaded as a zipped file. You

will need to unzip or extract it before proceeding.

(2) Place Landroid

on a secure and level surface. Turn the Main

Switch to the “O” position to turn off your Landroid

(3) Lift the rear of the Landroid

to access the underside.

(4) Open the protective rubber cover under the Landroid

to access

the USB port.

(5) Insert the USB drive (flash drive) in the port. (See Fig. K)

(6) Place the Landroid

on the ground again.

(7) Turn the Main Switch to the “I” position to turn on the Landroid

(8) The battery indication light will start to pulse. When the error

indication light flashes blue, the file has been copied.

(9) Without lifting the Landroid

, remove the USB drive (flash drive).

(10) The update will begin automatically and may take several

minutes. The final alert sequence will include a beep, and both

the battery indication light and error indication light will flash.

When the error indication light turns off and only the green

J1 J2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WR104 SI Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Worx WR104 SI

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info