Bedienungsanleitung Worx WX 680 Multitool (Seite 10 von 44) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

673120

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Oscillating Tool EN

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE:

The power tool is intended for sawing and

remodelling wooden materials, plastic,

plaster, non-ferrous metals and fasteners (e.g.

nails and clamps) as well as for working on

soft wall tiles and for dry grinding of small

surfaces. It is especially suitable for working

close to edges and for ﬂush cutting.

ASSEMBLY AND OPERATION

Action Figure

Mounting Accessories See Fig. A-C

Mounting The Sanding

Sheet

See Fig. D

Mounting The Suction

Device (not supplied)

See Fig. E1-E5

Operating The On/Off

Switch

See Fig. F

Using the Variable Speed

Dial

See Fig. G

The Variable Speed Dial can be used to set

the optimum oscillating frequency according

to the accessories used and the respective

application.

Oscillation

Frequency

Application

High oscillation

frequency

Sanding, sawing,

rasping and

polishing stone and

metal.

Low oscillation

frequency

Scraping, polishing

varnishes.

WORKING HINTS FOR YOUR

TOOL

If your power tool becomes too hot, especially

when used at low speed, set the speed to

maximum and run it with no load for 2-3

minutes to cool the motor. Avoid prolonged

usage at very low speeds. Always keep the

blade sharp.

Always ensure the workpiece is ﬁrmly held or

clamped to prevent movement.

Any movement of the material may affect the

quality of the cutting or sanding ﬁnish.

Start your tool before working and turn it off

only after you stop working.

Do not start sanding without having the

sandpaper ﬁtted.

Do not allow the sandpaper to wear away , it

will damage the sanding pad. The guarantee

does not cover sanding pad wear and tear.

Use coarse grit paper to sand rough surfaces,

medium grit for smooth surfaces and ﬁne grit

for ﬁnishing surfaces. If necessary, ﬁrst make

a test run on scrap material.

Excessive force will reduce the working

efﬁciency and cause motor overload.

Replacing the accessory regularly will

maintain optimum working efﬁciency.

MAINTAIN TOOLS WITH

CARE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

Your power tool requires no additional

lubrication or maintenance. There are no

user serviceable parts in your power tool.

Never use water or chemical cleaners to clean

your power tool. Wipe clean with a dry cloth.

Always store your power tool in a dry place.

Keep the motor ventilation slots clean. Keep

all working controls free of dust. Occasionally

you may see sparks through the ventilation

slots. This is normal and will not damage your

power tool.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or similarly qualiﬁed persons in order to

avoid a hazard

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX 680 Multitool Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info