575000
11
Zoom out
Zoom in
Vorherige Seite
1/96
Nächste Seite
11
Lithium-Ion Cordless Drill/Driver EN
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for driving in and
loosening screws as well as for drilling in
wood, metal and plastic.
ASSEMBLY AND OPERATION
Action Figure
BEFORE OPERATION
Removing the battery pack See Fig. A1
Charging the battery See Fig. A2
Installing the battery pack See Fig. A3
ASSEMBLY
CHUCK ADJUSTMENT
WARNING: Always lock off trigger
switch and disconnect tool from power
source when changing accessories. Always
ensure the bit is secure before starting the tool.
Damage to the Chuck or a loose bit may cause
possible personal injury.
--Removing the bits See Fig. B2
--Inserting the bits See Fig. B1
OPERATION
Forward/reverse rotation
control
WARNING: Never
change the direction
of rotation when the
chuck is rotating, wait
until it has stopped!
See Fig. C1,
C2, C3
TWO-SPEED GEAR
CONTROL
See Fig. D
TORQUE ADJUSTMENT
DRILLING,SCREWDRIVING,
HAMMER DRILLING
See Fig. E
Operating the on/off switch
WARNING: Do not
operate for long
periods at low speed
because excess heat will
be produced internally.
See Fig. F
LED Light Indicator
Before operation, the LED light will be
activated when the On/Off switch is slightly
depressed, and will automatically turn off 20
seconds after the On/Off switch is released.
The tool and battery are equipped with a
protection system. When the LED Light is
quickly flashing 3 seconds and turn off, the
system will automatically cut off power to
the tool to extend battery life. The tool will
automatically stop during operation if the tool
and/or battery are placed under one of the
following conditions:
Overloaded: The tool is operated in a
manner that causes it to draw an abnormally
high current. In this situation, release the
Trigger Switch on the tool and stop the
application that caused the tool to become
overloaded. Then pull the Trigger Switch again
to restart.
Overheated: Under the condition above, if
the tool does not start, the Tool and Battery are
overheated. In this situation, let the Tool and
Battery cool before pulling the Trigger Switch
again.
Low battery voltage: The remaining
Battery capacity is too low and the tool will not
operate. In this situation, remove and recharge
the Battery.
WARNING: To turn on the light, press
the On/Off switch and make sure the
Forward/Reverse Rotation Control is on
right/left position.
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Worx WX152 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info