Bedienungsanleitung Worx WX166.1 (Seite 11 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575008

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Lithium-Ion cordless drill/driver EN

higher speed and torque with increased

trigger pressure. Speed is controlled by the

amount of switch trigger depression.

WARNING: Do not operate for long

periods at low speed because

excess heat will be produced internally.

2. SWITCH LOCK

The switch trigger can be locked in the OFF

position. This helps to reduce the possibility of

accidental starting when not in use. To lock the

switch trigger, place the rotation control in the

center position.

3. REVERSIBLE (See Fig. C1, C2)

For drilling and screw driving use forward

rotation marked “ ” (lever is moved to the

left). Only use reverse rotation marked “ ”

(lever is moved to the right) to remove screws

or release a jammed drill bit.

WARNING: Never change the

direction of rotation when the

chuck is rotating, wait until it has

stopped!

4. TWO-SPEED GEAR CONTROL

(See Fig. D)

The drill has a two-speed gear control

designed for drilling or driving at LO (mark is

1) or HI (mark is 2) speeds. A slide switch is

located on top of the drill to select either LO

or HI speed. When using the drill in the LO

speed range, the speed will decrease and the

drill will have greater power and torque. When

using the drill in the HI speed range, the speed

will increase and the drill will have less power

and torque.

Gear I

Low speed range: For screwdriving or working

with large drilling diameter.

Gear II

High speed range: For working with small

drilling diameter.

WARNING: To prevent gear damage,

always allow the chuck to come to

a complete stop before changing the

direction of rotation or the two-speed

gear control.

5. CHUCK ADJUSTMENT (See Fig. E)

To open the chuck jaws rotate the front section

of the chuck. Insert the drill bit between the

chuck jaws and rotate the front section in the

opposite direction. Ensure the drill bit is in

the center of the chuck jaws. Finally, ﬁrmly

rotate the front chuck section in the opposite

directions. Your drill bit is now clamped in the

chuck.

6. TORQUE ADJUSTMENT (See Fig. F)

(Screw driving force of your drill driver)

The torque is adjusted by rotating the torque

adjustment ring. The torque is greater when

the torque adjustment ring is set on a higher

setting. The torque is less when the torque

adjustment ring is set on a lower setting.

Make the setting as follows:

1 - 4 For driving small screws

5 - 9 For driving screws into soft

material

10 - 15 For driving screws into soft and

hard material

For heavy drilling

7. AUTOMATIC SPINDLE LOCK

(See Fig. G)

The automatic spindle lock allows you to use

it as a regular screwdriver. You can give an

extra twist to ﬁrmly tighten a screw, loosen

a very tight screw or continue working

when the battery energy has expired. For

manual screwdriver purposes, the chuck is

automatically locked when the tool is off.

8. USING THE SIGHT LIGHT

To turn on the light simply press the on/off

switch. When you release the on/off switch,

the light will be off.

LED lighting increases visibility-great for

dark or enclosed area. LED is also a battery

capacity indicator. It will ﬂash when power

gets low.

9. DRILLING

When drilling into a hard smooth surface,

use a center punch to mark the desired hole

location. This will prevent the drill bit from

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX166.1 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info