Bedienungsanleitung Worx WX170 (Seite 10 von 12) (Englisch)

673235

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Lithium-Ion cordless

drill/driver

WX170 WX170.1 WX170.2 WX170.3

WX170.4 WX170.5 WX170.6 WX170.9

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for driving in and

loosening screws as well as for drilling in wood,

metal and plastic.

ASSEMBLY AND

OPERATION

ACTION FIGURE

BEFORE OPERATION

Removing the battery pack See Fig. A1

Charging the battery See Fig. A2

Installing the battery pack See Fig. A3

ASSEMBLY

CHUCK ADJUSTMENT

WARNING: Always lock off trigger switch

and disconnect tool from power source when

changing accessories. Always ensure the bit is secure

before starting the tool. Damage to the Chuck or a

loose bit may cause possible personal injury.

--Removing the bits See Fig. B1

--Inserting the bits See Fig. B2

OPERATION

FORWARD/REVERSE ROTATION

CONTROL

WARNING: Never change

the direction of rotation when

the chuck is rotating, wait until it has

stopped!

See Fig. C1,

C2, C3

TWO-SPEED GEAR CONTROL

See Fig. D

TORQUE ADJUSTMENT

DRILLING,SCREWDRIVING

See Fig. E

OPERATING THE ON/OFF SWITCH

WARNING: Do not operate

for long periods at low

speed because excess heat will be

produced internally.

See Fig. F

LED LIGHT INDICATOR

Before operation, the LED light will be activated when

the On/Off switch is slightly depressed.

WARNING: To turn on the light, press the On/

Off switch and make sure the Forward/Reverse

Rotation Control is on right/left position.

The tool and battery are equipped with a protection

system. When the LED Light is quickly ﬂashing 60

seconds and turn off, the system will automatically

cut off power to the tool to extend battery life. The

tool will automatically stop during operation if the

tool and/or battery are placed under one of the

following conditions:

• Overloaded: The tool is operated in a manner that

causes it to draw an abnormally high current. In this

situation, release the Trigger Switch on the tool and

stop the application that caused the tool to become

overloaded. Then pull the Trigger Switch again to

restart.

• Overheated: Under the condition above, if the tool

does not start, the Tool and Battery are overheated.

In this situation, let the Tool and Battery cool before

pulling the Trigger Switch again.

• Low battery voltage: The remaining Battery

capacity is too low and the tool will not operate. In

this situation, remove and recharge the Battery.

PROBLEM SOLUTION

1. WHY DOES THE DRILL NOT TURN ON WHEN

YOU PRESS THE SWITCH?

The forward/reverse rotation control, which is on

top of the trigger, is positioned in the lock function.

Unlock the forward/reverse rotation control by

putting it into the required rotation position. Push

the trigger and the drill will start to rotate.

2. THE DRILL STOPS BEFORE THE SCREW IS

COMPLETELY TIGHTENED. WHY?

Verify the torque position of the torque adjusting

ring, you can ﬁnd the torque-adjusting ring between

the chuck and the drill body. Position 1 is the lowest

torque (screw driving force) and position 15 is the

highest torque (screw driving force). Position is

for drill operation. Regulate the torque adjusting

ring to a higher position to reach the best result.

3. REASONS FOR DIFFERENT BATTERY PACK

WORKING TIMES

Charging time problems, as above, and having not

used a battery pack for a prolonged time will reduce

the battery pack working time. This can be corrected

after several charge and discharge operations by

charging & working with your drill. Heavy working

conditions such as large screws into hard wood will

use up the battery pack energy faster than lighter

working conditions. Do not re-charge your battery

pack below 0°C and above 45°C as this will affect

performance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX170 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info