Bedienungsanleitung Worx WX311 (Seite 9 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575021

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

Impact drill EN

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for impact drilling

in brick, concrete and stone as well as for

drilling in wood, metal and plastic.

1. AUXILIARY HANDLE (See Fig. A)

Slide the handle onto the drill and rotate

to the desired working position. To clamp

the auxiliary handle rotates the handgrip

clockwise. To loosen the auxiliary handles

rotate the hand grip anti-clockwise. Always

use the auxiliary handle.

WARNING! Always check and

rotate the handle tightly before

using to avoid any accident.

2. INSTALLING THE DEPTH GAUGE (See

Fig. B)

The depth gauge can be used to set a

constant depth to drill. To use the depth

gauge, loosen the handle by rotating the

bottom section of handle anti-clockwise.

Insert the depth gauge through hole in

handle. Slide the depth gauge to required

depth and tighten fully.

3. INSERTING A TOOL INTO CHUCK

(See Fig. C.1&C.2)

KEY CHUCK (9) (WX311)

Remove chuck key from key storage tab

at base of drill handle, then place key into

chuck, turn key anti-clockwise to undo/

loosen chuck, inset drill/tool and ﬁrmly

tighten chuck by turning key clockwise.

Remove key and replace in storage tab at

base of drill handle (See Fig C.1).

KEYLESS CHUCK (1) (WX311.1)

To open the chuck jaws rotate the front

section of the chuck while holding the rear

section. Insert the drill bit between the

chuck jaws and rotate the front section in

the opposite direction while holding the

rear section. Ensure that the drill bit is in the

center of the chuck jaws. Finally, ﬁrmly rotate

the two separate chuck sections in opposite

directions. Your drill bit is now locked in the

chuck. (See Fig C.2)

4. ON/OFF SWITCH

Depress to start and release to stop your

tool.

It is also a variable speed switch that delivers

higher speed and torque with increased

trigger pressure. Speed is controlled by the

amount of switch trigger depression.

5. SWITCH LOCK-ON BUTTON (See Fig.

Depress on/off switch (7) then lock-on button

(5), release on/off switch ﬁrst and lock-on

button second. Your switch is now locked on

for continuous use. To switch off your tool

just depress and release the on/off switch.

6. FORWARD AND REVERSE ROTATION

CONTROL (See Fig. E)

For drilling and screw driving use forward

rotation marked “



” (lever is moved to

the left). Only use reverse rotation marked

“



” (lever is moved to the right) to remove

screws or release a jammed drill bit.

WARNING! Never change the direction

of rotation when the tool is rotating,

wait until it has stopped.

7. HAMMER OR DRILLING CONTROL

(See Fig. F)

When drilling masonry and concrete choose

the Hammer position “

“When drilling

wood, metal, plastic and screw driving

choose the Drill position”

“.

8. GEAR BOX SWITCH

Choose position I (See Fig. G)for high

torque/low speed range for large diameter

drill bits and screw driving. Choose position

II (See Fig. H)

for low torque/ High-speed range for small

diameter drill bits. If the gears do not engage

easily then rotate the chuck by hand to align

the gears. Never change the gears when the

tool is rotating, wait until it has stopped.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX311 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info