Bedienungsanleitung Worx WX318 (Seite 9 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

673227

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Impact drill EN

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for impact drilling in

brick, concrete and stone as well as for drilling

in wood, metal and plastic.

ASSEMBLY AND OPERATION

ACTION FIGURE

Clamping and loosening the

Auxiliary Handle

WARNING! Always

check and rotate the

handle tightly before using to

avoid any accident.

See Fig. A1,

Installing the Depth Gauge See Fig. B

Inserting Bits into Chuck See Fig. C1, C2

Plugging in the power See Fig. D

On/Off Switch and Lock-on

Button

See Fig. E

Variable Speed Control See Fig. F

Forward and Reverse

Rotation Control

NOTE: Never move

the forward/reverse

switch whilst the drill in

operation or the on/off

switch is locked as this

will damage the drill.

See Fig. G

Hammer or Drilling Control See Fig. H

WORKING HINTS FOR YOUR

DRILL

1. Drilling masonry and concrete

Select the drill/impact action selector switch

to the “hammer symbol” position. Tungsten

carbide drill bits should always be used for drilling

masonry, concrete etc with a high speed.

2. Drilling steel

Select the drill/impact action selector switch to

the “drill symbol” position. HSS drill bits should

always be used for drilling steel with a lower

speed.

3. Pilot holes

When drilling a large hole in tough material (i.e.

steel), we recommend drilling a small pilot hole

ﬁrst before using a large drill bit.

4. Drilling tiles

Select the drill/impact action selector switch to

the “drill symbol” position to drill the tile. When

tile has been penetrated, switch over to “hammer

symbol” position.

5. Cool the motor

If your power tool becomes too hot, set the speed

to maximum and run no load for 2-3 minutes to

cool the motor.

MAINTENANCE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

Your power tool requires no additional

lubrication or maintenance.

There are no user serviceable parts in your

power tool. Never use water or chemical

cleaners to clean your power tool. Wipe clean

with a dry cloth. Always store your power tool

in a dry place. Keep the motor ventilation slots

clean. Keep all working controls free of dust.

Occasionally you may see sparks through the

ventilation slots. This is normal and will not

damage your power tool.

If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent or similarly

qualiﬁed persons in order to avoid a hazard.

If the replacement of the supply cord is necessary,

this has to be done by the manufacturer or his

agent in order to avoid a safety hazard.

TROUBLESHOOTING

1. If your power tool does not start, check the

plug on the power supply ﬁrst.

2. If the drill doesn’t work properly, check the

drill bit for sharpness, replace drill bit if

worn. Check that the drill is set to forward

rotation for normal use.

3. If a fault can not be rectiﬁed, return the tool

to an authorized dealer for repair

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX318 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info