Bedienungsanleitung Worx WX330.2 (Seite 10 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

575146

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Rotary hammer EN

use. To switch off your tool just depress and

release the on/off switch.

7. AUXILIARY HANDLE

Slide the handle onto the drill and rotate to

the desired working position. To clamp the

auxiliary handle rotates the handle clockwise.

To loosen the auxiliary handle rotate the

handle anti-clockwise (See Fig. E).

WARNING: Always use the auxiliary

handle.

8. FORWARD AND REVERSE ROTATION

CONTROL

With the drill pointing away from you, push

the forward/reverse-lever (3) to the left

“ “for forward rotation. Push the forward/

reverse-lever (3) to the right for reverse

rotation “ “.

WARNING: Never change the

direction of rotation while the tool

is rotating, wait until it has stopped.

9. ADJUSTABLE DEPTH STOP

Fit the drill bit into the chuck. Loosen the depth

stop by rotating the handle anti-clockwise.

Slide the depth stop until the distance

between the depth stop end and the drill bit

end is equal to the depth of hole/screw you

wish to make. Then clamp the depth stop by

rotating the handle clockwise.

10. FUNCTION MODE SELECTION (See Fig. F)

The operation of the gearbox for each

application is set with the function mode

selection switch (4), To change between

functions, depress the unlocking button

(15) and rotate the selector to the desired

operating mode.

For simultaneous drilling and impacting of

concrete or masonry, choose the Hammer

drilling position.

For screw driving, drilling into steel, wood and

plastics choose the Rotary drilling position.

For impacting only - for light chipping,

chiseling and demolition applications choose

the Hammer position.

WARNING: The operating mode

selector switch may be actuated

only at a standstill.

WARNING: Prolonged use will cause

the aluminum housing to become

hot, do not touch.

WORKING HINTS FOR

YOUR DRILL (HAMMER)

If your power tool becomes over heated, set

the speed to maximum and run no load for 2-3

minutes to cool the motor. SDS-plus tungsten

carbide drill bits should always be used for

concrete and masonry. When drilling in metal,

only use HSS drill bits in good condition.

Always use a magnetic bit holder when using

short screwdriver bits. Where possible use a

pilot hole before drilling a large diameter hole.

MAINTENANCE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

Your power tool requires no additional

lubrication or maintenance. There are no user

serviceable parts in your power tool. Never

use water or chemical cleaners to clean your

power tool. Wipe clean with a dry cloth.

Always store your power tool in a dry place.

Keep the motor ventilation slots clean. Keep

all working controls free of dust.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or similarly qualiﬁed persons in order to

avoid a hazard.

ENVIRONMENTAL

PROTECTION

Waste electrical products should not

be disposed of with household waste.

Please recycle where facilities exist.

Check with your local authorities or retailer for

recycling advice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX330.2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info