Bedienungsanleitung Worx WX368.1 (Seite 12 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575043

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Lithium-Ion cordless hammer drill EN

housing on the back of the drill. It can be used to

keep the drill level during vertical drilling operation.

11. DRILLING

When drilling into a hard smooth surface,

use a center punch to mark the desired whole

location. This will prevent the drill bit from

slipping off center as the hole is started. Hold

the tool ﬁrmly and place the tip of the bit at

the point to be drilled. Depress the switch

trigger to start the tool. Move the drill bit into

the workpiece, applying only enough pressure

to keep the bit cutting. Do not force or apply

side pressure to elongate a hole.

Tungsten carbide drill bits should

always be used for concrete and

masonry. When drilling in metal, only use

HSS drill bits in good condition. Always

use a magnetic bit holder (not included)

when using short screwdriver bits. When

screw-driving, apply a small quantity

of liquid soap or similar to the screw

threads to ease insertion.

12. DISPOSAL OF AN EXHAUSTED

BATTERY PACK

To preserve natural resources, please

recycle or dispose of the battery pack

properly. This battery pack contains

Lithium batteries.

Consult your local waste authority for

information regarding available recycling and/

or disposal options. Discharge your battery

pack by operating your drill, then remove the

battery pack from the drill housing and cover

the battery pack connections with heavy-duty

adhesive tape to prevent short circuit and

energy discharge. Do not attempt to open or

remove any of the components.

PROBLEM SOLUTION

1. WHY DOES THE DRILL NOT TURN ON

WHEN YOU PRESS THE SWITCH?

The forward and reverse switch, which is on

top of the trigger, is positioned in the lock

function. Unlock the forward and reverse

switch putting it into the required rotation

position. Push the trigger and the drill will

start to rotate (See Fig.B).

2. THE DRILL STOPS BEFORE THE

SCREW IS COMPLETELY TIGHTENED.

WHY?

Verify the torque position of the torque

adjustment ring, you can ﬁnd the torque

adjustment ring between the chuck and the

drill body. Position 1 is the lowest torque

(screw driving force) and position 20 is the

highest torque (screw driving force). Position

is for drill operation. Regulate the torque

adjustment ring to a higher position to reach

the best result (See Fig.E).

3. I CAN NOT FIT THE BATTERY INTO

THE BATTERY CHARGER. WHY?

The battery can be inserted into the charger

only in one direction. Turn the battery around

until it can be inserted into the slot, the red

LED light should turn on when the battery is

charging.

4. REASONS FOR DIFFERENT CHARGING

TIMES

Charging time problems, as above, and

having not used a battery pack for a prolonged

time will reduce the battery pack working time.

This can be corrected after several charge and

discharge operations by charging & working

with your drill. Heavy working conditions such

as large screws into hard wood will use up the

battery pack energy faster than lighter working

conditions. Do not re-charge your battery pack

below 0

C and above 30

C as this will affect

performance.

MAINTENANCE

Remove the battery pack from the tool

before carrying out any adjustment,

servicing or maintenance.

There are no user serviceable parts in your

power tool. Never use water or chemical

cleaners to clean your power tool. Wipe clean

with a dry cloth. Always store your power tool

in a dry place. Keep the motor ventilation slots

clean. Keep all working controls free of dust.

Occasionally you may see sparks through the

ventilation slots. This is normal and will not

damage your power tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX368.1 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info