Bedienungsanleitung Worx WX372.1 (Seite 10 von 96) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

575019

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Lithium-Ion cordless hammer drill EN

1110

left). Only use reverse rotation marked “ ”

(lever is moved to the right) to remove screws

or release a jammed drill bit.

WARNING: Never change the

direction of rotation when the

chuck is rotating, wait until it has

stopped!

4. TWO-SPEED GEAR CONTROL (See Fig.C)

The drill has a Two-Speed Gear Control (3)

designed for drilling or driving at LO (mark is

1) or HI (mark is 2) speeds. A slide switch is

located on top of the drill to select either LO

or HI speed. When using the drill in the LO

speed range, the speed will decrease and the

drill will have greater power and torque. When

using the drill in the HI speed range, the speed

will increase and the drill will have less power

and torque.

Gear I

Low speed range: for screwdriving or working

with large drilling diameter.

Gear II

High speed range: for working with small

drilling diameter.

WARNING: To prevent gear damage,

always allow the chuck to come

to a complete stop before changing the

direction of rotation or the two-speed

gear train.

5. CHUCK ADJUSTMENT (See Fig.D)

To open the chuck jaws rotate the front section

of the chuck (1). Insert the drill bit between

the chuck jaws and rotate the front section in

the opposite direction. Ensure the drill bit is

in the center of the chuck jaws. Finally, ﬁrmly

rotate the front chuck section in the opposite

directions. Your drill bit is now clamped in the

chuck.

6. TORQUE ADJUSTMENT AND HAMMER

OR DRILLING CONTROL (See Fig.E)

(Screw driving force of your drill driver)

The torque is adjusted by rotating the torque

adjustment ring (2). The torque is greater

when the torque adjustment ring is set on

a higher setting. The torque is less when

the torque adjustment ring is set on a lower

setting.

When drilling in masonry and concrete choose

the hammer position

When drilling in wood, metal, plastic and

screwdriver choose the drill position .

Make the setting as follows:

1 - 4 for driving small screws

5 - 9

for driving screws into soft

material

10 - 14

for driving screws into soft and

hard material

15 - 19 for driving screws into hard wood

20 - 22 for driving larger screws

for heavy drilling

for drilling in Brickwork and

concrete

7. AUTOMATIC SPINDLE LOCK

The automatic spindle lock allows you to

use as a regular screwdriver. You can give an

extra twist to ﬁrmly tighten a screw, loosen

a very tight screw or continue working

when the battery energy has expired. For

manual screwdriver purposes, the chuck is

automatically locked when the tool is off.

8. SIGHT LIGHT

The Sight Light (8) allows you to keep a clear

view under less illuminated circumstances.

To turn on the light simply press the on/off

switch. When you release the on/off switch,

the light will go out.

9. DRILLING

Drilling

Set the Torque adjustment ring to the “Drilling

without impact” symbol . The safety clutch is

deactivated in the “Drilling” position.

Impact Drilling

Set the Torque adjustment ring to the “Impact

drilling” symbol . In the “Impact drilling”

position, the safety clutch is deactivated and

the maximum power is always effective.

Move the drill bit into the workpiece, applying

only enough pressure to keep the bit cutting.

Do not force or apply side pressure to

elongate a hole.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX372.1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info