Bedienungsanleitung Worx WX382.1 (Seite 11 von 96) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

575148

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Cordless rotary hammer EN

1110

— REMOVING (See Fig. B3)

Retract back the bit holder locking sleeve (2)

and pull out the bit.

WARNING: Your new WORX Rotary

Hammer Drill generates powerful

forces to get your job done quickly and

effectively. These forces may cause

inferior quality SDS bits to break and jam

in the chuck, We therefore recommend

that only high quality SDS bits be used

with this tool.

2. INSERTING A TOOL INTO CHUCK (13)

(See Fig. C)

To open the chuck jaws rotate the front section

of the chuck while holding the rear section.

Insert the drill bit between the chuck jaws

and rotate the front section in the opposite

direction while holding the rear section.

Ensure that the drill bit is in the center of

the chuck jaws. Finally, ﬁrmly rotate the two

separate chuck sections in opposite directions.

Your drill bit is now locked in the chuck.

3. ON/OFF SWITCH (See Fig. D)

Depress the On/Off switch (4) to start and

release it to stop your tool.

— ON/OFF SWITCH WITH VARIABLE

SPEED CONTROL

Depress the On/Off switch to start and release

it to stop your tool. This tool has a variable

speed switch (4) that delivers higher speeds

with increased trigger pressure - speed is

controlled by varying the pressure applied to

the switch.

4. SWITCH LOCK (See Fig. D)

The switch trigger can be locked in the OFF

position. This helps to reduce the possibility of

accidental starting when not in use. To lock the

switch trigger, place the direction of rotation

control in the center position.

5. FORWARD AND REVERSE ROTATION

CONTROL (See Fig. D)

With the hammer pointing away from you, push

the forward/reverse-lever “

“ to the left for

forward rotation. Push the forward/reverse-lever “

“ to the right for reverse rotation.

WARNING: Never change the

direction of rotation while the tool

is rotating, wait until it has stopped.

6. FUNCTION MODE SELECTION

(See Fig. E)

The operation of the gearbox for each

application is set with the function mode

selection switch (8). To change between

functions, depress the unlocking button

(15) and rotate the selector to the desired

operating mode.

For simultaneous

drilling and impacting

of concrete or masonry,

choose the Hammer

drilling position.

For screw driving,

drilling into steel, wood

and plastics choose the

Rotary drilling position.

WARNING: The operating mode

selector switch may be actuated

only at a standstill.

7. LED LIGHT (See Fig. F)

To turn on the light simply press the on/off

switch. When you release the on/off switch,

the light will be off.

LED lighting increases visibility-great for

dark or enclosed area. LED is also a battery

capacity indicator. It will ﬂash when power

gets low.

8. TEMPERATURE DEPENDENT

OVERLOAD PROTECTION

When using as intended for, the power tool

cannot be subject to overload. When the

load is too high or the allowable battery

temperature of 75°C is exceeded, the

electronic control switches off the power

tool until the temperature is in the optimum

temperature range again.

9. PROTECTION AGAINST DEEP

DISCHARGING

The Li-Ion battery is protected against deep

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX382.1 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info