Bedienungsanleitung Worx WX425 (Seite 10 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575066

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Circular saw EN

1110

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE:

The machine is intended for lengthways

and crossways cutting of wood with straight

cutting lines as well as bevel angles to 45°

while resting ﬁrmly on the work piece.

1. DEPTH OF CUT ADJUSTMENT

(See Fig. A)

Lift the depth of cut lock lever and raise the

saw body away from the base plate. Set the

depth of cut with the scale and push the lever

down to lock. Always add 3mm to your depth

of cut so that the blade can cut through the

material.

2. BASE PLATE ANGLE ADJUSTMENT

(See Fig. B1 & B2)

Lift the base plate bevel lock to loosen and

rotate the base plate to desired bevel angle

with the scale provided. Push the bevel lock

down to clamp the base plate position. Check

the angle and ensure that the base plate is

ﬁrmly secured. The angle markings on the

base plate are accurate for most general

purposes but it is recommended to set the

angle with a protractor and make a test cut on

other material for accurate work. Do not use

the depth of cut scale when making bevel cuts

due to possible inaccuracy.

USING THE CIRCULAR SAW

1. SAFETY ON/OFF SWITCH (See Fig. C)

Your switch is locked off to prevent accidental

starting. Depress the lock off button then

the on/off switch and release the lock off

button. Your switch is now on. To switch off,

just release the on/off switch. The blade may

continue to rotate after switching off. Wait until

the machine comes to a complete stop before

setting down.

2. PARALLEL GUIDE ADJUSTMENT

(See Fig. D1,D2)

It is used for making cuts parallel to a

workpiece edge at a chosen distance. Slide

the parallel guide arm through the ﬁxture to

achieve the required cutting distance then

tighten the lock knob (18) to clamp.

CUTTING GUIDE

For WX425 (See Fig. D2)

The Beveltrac

(3) ﬁxed in front of the base

plate is used as cutting guide.

3. HAND GRIP POSITION (See Fig. E)

Always hold your saw ﬁrmly with both hands

when operating.

4. FITTING / REPLACING A SAW BLADE

(See Fig. F, G, H)

Press the spindle lock button and use the hex

key to loosen and remove the blade bolt (13).

Remove the washer (B) and the outer ﬂange

(C). Rotate the lower blade guard clockwise

by pushing the guard lever to take out the old

blade (12). Fit a replaced blade. Ensure that

the blade bore is located on the inner ﬂange

(D) and the blade direction arrow points in

the same direction as the lower blade guard

arrow. Place the outer ﬂange, the washer

and the blade bolt onto the blade bore. Press

the spindle lock again and use the hex key to

tighten the bolt with 1/4 turn more than ﬁnger

tight. Check if the blade is securely clamped.

WARNING: Blade teeth are very

sharp. For best cutting results ensure

you use a saw blade suited to the material and

cut quality you need.

5. DUST EXTRACTION OUTLET (See Fig. I)

To remove sawdust, connect a suitable

external dust extraction machine (e.g. vacuum

cleaner) to the dust extraction outlet with

the vacuum adaptor and a ﬂexible hose

connection. Ensure the hose connection is

secure.

6. HEX KEY STORAGE (See Fig. J)

The hex key provided with the saw can be

placed in the storage area located at back of

the base plate.

7. ACCESSIBLE MOTOR BRUSH

REPLACEMENT (See Fig. K)

There are two replaceable motor brushes

which can be easily accessed on either the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX425 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info