Bedienungsanleitung Worx WX426 (Seite 13 von 142) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

575056

Zoom out

Zoom in

Vorherige Seite

1/142

Nächste Seite

Electric Circular Saw EN

or pinched by the workpiece, the edge of the

wheel that is entering into the pinch point can

dig into the surface of the material causing

the wheel to climb out or kick out. The wheel

may either jump toward or away from the

operator, depending on direction of the

wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse

and/or incorrect operating procedures or

conditions and can be avoided by taking

proper precautions as given below.

a) Maintain a ﬁrm grip on the power

tool and position your body and

arm to allow you to resist kickback

forces. Always use auxiliary handle, if

provided, for maximum control over

kickback or torque reaction during

start-up. The operator can control torque

reactions or kickback forces, if proper

precautions are taken.

b) Never place your hand near the

rotating accessory. Accessory may

kickback over your hand.

C) Do not position your body in line with

the rotating wheel. Kickback will propel

the tool in direction opposite to the wheel’s

movement at the point of snagging.

d) Use special care when working

Corners, sharp edges etc. Avoid

bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain,

woodcarving blade, segmented

diamond wheel with a peripheral

gap greater than 10 mm or toothed

saw blade. Such blades create frequent

kickback and loss of control.

f) Do not “jam” the wheel or apply

excessive pressure. Do not attempt

to make an excessive depth of cut.

Overstressing the wheel increases the

loading and susceptibility to twisting or

binding of the wheel in the cut and the

possibility of kickback or wheel breakage.

g) When wheel is binding or when

interrupting a cut for any reason,

switch off the power tool and hold

the power tool motionless until the

wheel Comes to a complete stop.

Never attempt to remove the wheel

from the cut while the wheel is in

motion otherwise kickback may occur.

lnvestigate and take corrective action to

eliminate the cause of wheel binding.

h) Do not restart the cutting operation

in the workpiece. Let the wheel reach

full speed and carefully re-enter the

cut. The wheel may bind, walk up or

kickback if the power tool is restarted in the

workpiece.

i ) Support panels or any oversized

workpiece to minimize the risk of

wheel pinching and kickback. Large

workpieces tend to sag under their own

weight. Supports must be placed under the

workpiece near the line of cut and near the

edge of the workpiece on both sides of the

wheel.

j) Use extra caution when making a

“pocket cut” into existing walls or

other blind areas. The protruding wheel

may cut gas or water pipes, electrical

wiring or objects that can cause kickback.

GENERAL SAFETY

WARNINGS FOR YOUR

LASER

WARNING: Read all safety warnings

and all instructions. Failure to follow

the warnings and instructions may result in

serious injury.

Save all warnings and instructions for

future reference.

These lasers do not normally present an

optical hazard although staring at the

beam may cause ﬂash blindness.

Do not stare directly at the laser beam. A

hazard may exist if you deliberately stare

into the beam, please observe all safety

rules as follows:

1) The laser shall be used and maintained

in accordance with the manufacturer’s

instructions.

2) Never aim the beam at any person or

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX426 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info