Bedienungsanleitung Worx WX426 (Seite 16 von 142) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

575056

Zoom out

Zoom in

Vorherige Seite

1/142

Nächste Seite

Electric Circular Saw EN

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE:

The tool is intended for ripping and cross-

cutting wood and other materials in straight

cutting lines, while resting ﬁrmly on the work

piece.

ASSEMBLY AND OPERATION

Action Figure

Saw blade Assembly and

Removing

See Fig. A

Safety On/Off Switch See Fig. B

Cross And Rip Cutting See Fig. C1, C2

Cutting Depth Adjusting See Fig. D1, D2

Using the laser light

feature

See Fig. E

Replacing laser batteries See Fig. F1-F3

Parallel Guide See Fig. G1 G2

Pocket Cutting See Fig. H1 H2

Sawdust Removal See Fig. I

WORKING HINTS FOR YOUR

TOOL

If your power tool becomes too hot, please

run your circular saw no load for 2-3 minutes

to cool the motor. Avoid prolonged usage at

very low speeds.

Protect saw blades against impact and shock.

Cutting with extreme force can signiﬁcantly

reduces the performance capability of the tool

and reduces the service life of the saw blade.

Sawing performance and cutting quality

depend essentially on the condition and the

tooth count of the saw blade. Therefore, use

only sharp saw blades that are suited for the

material being cut.

Choice of blades: 24 teeth for general work,

approx. 40 teeth for ﬁner cuts, more than 40

teeth for very ﬁne cuts into delicate surfaces,

diamond for tile, cement board, etc.

Only use saw blades recommended.

MAINTAIN TOOLS WITH

CARE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

Keep tools sharp and clean for better and

safer performance. Follow instructions for

lubricating and changing accessories. Inspect

tool cords periodically and if damaged, have

repaired by authorized service facility. Your

power tool requires no additional lubrication

or maintenance. There are no user serviceable

parts in your power tool. Never use water or

chemical cleaners to clean your power tool.

Wipe clean with a dry cloth. Always store

your power tool in a dry place. Keep the

motor ventilation slots clean. Keep all working

controls free of dust.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or similarly qualiﬁed persons in order to

avoid a hazard.

Periodically clear dust and chips from guard

and base to ensure proper performance.

ENVIRONMENTAL

PROTECTION

This product has been marked with a

symbol relating to removing electric

and electronic waste. This means that

this product shall not be discarded with

household waste but that it shall be returned

to a collection system which conforms to the

European Directive 2002/96/CE. It will then

be recycled or dismantled in order to reduce

the impact on the environment. Electric and

electronic equipment can be hazardous for the

environment and for human health since they

contain hazardous substances.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX426 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info