Bedienungsanleitung Worx WX570 BLADERUNNER (Seite 13 von 143) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575088

Zoom out

Zoom in

Vorherige Seite

1/143

Nächste Seite

Multi-function saw EN

2. GUARD ARM ALIGNMENT (See Fig. G)

For your convenience, the guard arm has

already been adjusted to be aligned with

the placement of the blade at the factory.

However, you may also adjust it by following

the instructions below:

(a) Loosen guard arm clamp knob (9).

(b) Loosen adjustment screw (d) under the

arm pivot.

along the support arm until the blade

locates exactly between the guide bearings

without any bending of the blade.

(d) Tighten the locking knob, tighten the

adjustment screw.

OPERATION

WARNING: Always wear safety

goggles or safety glasses with side

shields when operating tools. Failure to do so

could result in objects being thrown into your

eyes causing possible serious injury.

WARNING: Do not use any attachments

or accessories not recommended by

the manufacturer. The use of attachments or

accessories not recommended can result in

serious personal injury.

WARNING: To reduce the risk of injury,

the operator should use the accessory

or attachment according to the instruction.

The tool should be operated at the speed in

accordance with pertinent factors such as:

(a) The dimensions and material of the work

piece;

(b) The size and type of the saw blade.

WARNING: Operating the saw

according to the instruction, never cut

without the guard in place.

WARNING: When lifting or lowering

the guard arm, as indicated in ﬁgure

A2, make sure to avoid putting your ﬁngers

between the gaurd arm and the support arm.

1. ON/OFF SWITCH (See Fig. H)

To turn the machine on, press the on switch (2).

To turn it off, press the off switch (1).

2. VARIABLE SPEED CONTROL

(See Fig. I.1)

The variable speed control is under the work

table. Adjust the variable speed control to

increase or decrease the speed, 6 being the

highest and 1 being the lowest. Speed should

be adjusted according to material thickness

and blade speciﬁcation to be used. Speed

can be adjusted during both load or no load

operation. See Chart 1 for general guidance on

speed selection.”

NOTE: Avoid prolonged use at very low

speed as this may damage your

BladeRunner

’s motor.

Chart 1

Material Speed setting

Wood 5-6

Steel 3-4

Aluminum 4-6

PVC 3-4

Ceramic 3-5

IMPORTANT NOTE: When you cut ceramic,

please use a low feed rate at the end of your

cut. This will help decrease cracking at the end.

We suggest you use a wooden push stick to

complete the cut in ceramic (See Fig. I.2).Push

in the middle of ceramic piece to support it.

Remember to use a vacuum to collect

dust anytime tile is being cut.

GENERAL CUTTING RULES:

(a) ALWAYS allow the blade to reach

operating speed before commencing a

cut.

(b) ALWAYS wait until the blade has

completely stopped before removing

a workpiece or off-cut from close to

the blade.

feed rate which allows the blade to

cut freely without excessive force.

(d) NEVER force a blunt blade to cut with

excessive pressure.

(e) NEVER hold or push the work with

hands in line with the blade.

(f) NEVER operate the BladeRunner

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX570 BLADERUNNER Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info