Bedienungsanleitung Worx WX625 (Seite 12 von 128) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575097

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Perpendicular planer EN

13 12

downward and sideways pressure.

NOTE: The perpendicular planer cannot

correct work where the reference face is

twisted.

D. STRAIGHTENING AN EDGE

The Lower Datum Edge (18.6) of the

Perpendicular Fence can be used to plane

a straight and perpendicular edge on an

inaccurate or irregular edged workpiece.

Mark the position of the desired straight edge

at each end of the workpiece.

Measure an offset of dimension below these

positions and mark again.

Clamp a straight edge (trusted wood batten

or steel section) to the work, its top surface

aligned with the offset marks.

Commence planing the edge, keeping material

removal reasonably even along the edge,

however this is not critical.

As the planed edge approaches the desired

position, reduce the planing set depth if

necessary for the best ﬁnish for the last few

passes before the Lower Datum Edge contacts

the straight edge.

NOTE: Tapers can also be produced by

adjusting the position of the straight

edge.

E. FINE TUNING THE PERPENDICULAR

FENCE

The Perpendicular Fence is factory adjusted,

however the accuracy can be ﬁne tuned by the

user.

Use a square to check the fence at each end.

Loosen the lock nut (18.1) and rotate the

turnbuckle to move the fence in the correct

direction.

Only small adjustments, typically less than 1

turn should be needed.

Re-check with the square and when satisﬁed

hold the turnbuckle whilst retightening the lock

nut.

There is no need to excessively tighten the

lock nut, just tight is sufﬁcient.

Repeat for each end of the fence.

WORKING HINTS FOR YOUR

PLANER

WARNING: Danger of kickback!

Apply the machine to the work

piece only when switched on.

1. STANDARD SURFACE PLANING

Set the desired cutting depth. Position the

front part of the base plate ﬂat onto the work

surface. Switch the machine on and push your

planer forward and it will start cutting, always

maintain all of the base plate ﬂat on the work

surface to prevent the cutting blade jumping.

Move the plane evenly over the work surface.

For most applications 0-2mm max cutting

depth will produce a good surface ﬁnish. It is

best to use small depths of cut and repeat the

planning process.

2. EDGE CHAMFERING

Using the V-groove in the base plate (15) you

can make a chamfer on the work piece edge

(See Fig. I). Guide the planer along the edge

and maintain a constant angle and force to

produce a good ﬁnish. You can control the

angle of the chamfer with your hands. Make a

test chamfer on a scrap piece of wood. Ensure

your work piece is clamped and supported

near the edge.

3. REBATING

Fit the Rebate Depth Gauge (16) to your

planer. Set the required rebate depth using

the scale and the mark on the planer housing

next to the scale. Rebate width is set using

the Perpendicular Fence (See Fig. J).Loosen

locking knob (18.4) and adjust the required

rebating width (max 82mm). Tighten locking

knob (18.4) Adjust the desired rebating depth

with the rebating depth gauge (16) accordingly

(max 9mm) (See Fig. K).Plane as often as

necessary to achieve the desired rebating

depth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX625 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info