Bedienungsanleitung Worx WX642 (Seite 10 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

673277

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Finishing Sander EN

clamped to prevent movement.

Any movement of the material may affect the

quality of the sanding ﬁnish.

Start your sander before sanding and turn it

off only after you stop sanding. For the best

results, sand wood in the direction of the grain.

Do not start sanding without having the

sandpaper ﬁtted.

Do not allow the sandpaper to wear away it

will damage the base-plate. The guarantee

does not cover base-plate wear and tear.

Use coarse grit paper to sand rough surfaces,

medium grit for smooth surfaces and ﬁne grit

for the ﬁnal surfaces. If necessary, ﬁrst make a

test run on scrap material.

Use only good quality sandpaper.

The sandpaper controls the sanding efﬁciency,

not the amount of force you apply to the

tool. Excessive force will reduce the sanding

efﬁciency and cause motor overload.

Replacing the sandpaper regularly will

maintain optimum sanding efﬁciency.

MAINTENANCE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

Your power tool requires no additional

lubrication or maintenance. There are no user

serviceable parts in your power tool. Never

use water or chemical cleaners to clean your

power tool. Wipe clean with a dry cloth.

Always store your power tool in a dry place.

Keep the motor ventilation slots clean. Keep all

working controls free of dust. Occasionally you

may see sparks through the ventilation slots.

This is normal. If the supply cord is damaged,

it must be replaced by the manufacturer, its

service agent or similarly qualiﬁed persons in

order to avoid a hazard.

ENVIRONMENTAL

PROTECTION

Waste electrical products must not be

disposed of with household waste.

Please recycle where facilities exist.

Check with your local authorities or retailer for

recycling advice.

PLUG REPLACEMENT

( UK & IRELAND ONLY )

If you need to replace the ﬁtted plug then

follow the instructions below.

IMPORTANT

The wires in the mains lead are colored in

accordance with the following code:

BLUE = NEUTRAL

Brown = Live

As the colors of the wires in the mains lead of

this appliance may not correspond with the

colored markings identifying the terminals

in your plug, proceed as follows. The wire

which is colored blue must be connected to

the terminal which is marked with N. The wire

which is colored brown must be connected to

the terminal which is marked with L.

WARNING! Never connect live or neutral

wires to the earth terminal of the plug. Only

ﬁt an approved 13ABS1363/A plug and the

correct rated fuse.

NOTE: If a moulded plug is ﬁtted and has to

be removed take great care in disposing of the

plug and severed cable, it must be destroyed

to prevent engaging into a socket.

Connect

Blue to N

(neutral)

Outer sleeve

firmly clamped

Cable grip

Brown L (live)

13 Amp fuse approved

to BS1362

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX642 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info