Bedienungsanleitung Worx WX653 (Seite 9 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

575092

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Random orbital sander EN

start the machine.

Depress “0” on the sliding on-off switch to

stop it.

2. VARIABLE SPEED CONTROL

(See Fig D)

With the variable speed control dial (7), the

required speed can be selected (also while

running).

The required speed is dependent on the

material and is to be determined by a practical

trial.

After longer periods of working at low speed,

allow the machine to cool down by running it

for approx. 3 minutes at maximum speed with

no load.

Sanding

work

Grain

Speed

setting(opm)

Coarse

sanding

Precision

sanding

Sanding

down

varnishes

180 400 8700~11000

Stripping

paint

40 120 9800~11000

Touching

paintwork

120 120 7600~10000

Sanding

wood

60 240 7600~11000

Machining

veneer

180 400 8700~11000

Sanding

aluminium

80 240 7600~11000

Derusting

metal

40 120 9800~11000

Sanding

metal and

steel

120 240 9800~11000

Sanding

plexiglass

180 400 6500~8700

3. DUST BOX (See Fig E, F)

A) Attach the dust box (See Fig E)

Your sander is equipped with a dust collection

box. To attach, slide the dust box onto the

outlet piece and take care that the dust box

locks in the grooves of the outlet.

CAUTION: To prevent the possibility

of sanding dust or foreign body being

thrown into your face or eyes, never attempt

to use your sander without the dust box

properly installed.

B) Empty dust box (See Fig F)

For more efﬁcient operation, empty dust box

every 5-10mins. This will permit the air to ﬂow

through the box better. To empty the dust box,

pull off the dust box out of the dust extraction

outlet directly and shake out dust.

4. USING THE DUST EXTRACTION

ADAPTER (See Fig G)

Your sander is equipped with two dust

extraction adapters, which are designed for

connecting the hose of a vacuum cleaner.

If the vacuum hose is 35mm, Insert the 35mm

dust adapter (a) directly into the rear dust

outlet of sander. If the vacuum hose is 32 mm,

insert the 32 mm adapter (b) into the back of

35mm adapter (a).

NOTE: Please pull the dust adapter to make

sure tightened securely on the dust outlet.

5. SANDING SURFACES

Place the machine with the complete Sand

paper on the surface to be worked. Ensure

uniform sanding pressure. Less sanding

pressure increases the sanding capacity and

protects the machine and the sanding tool.

The removal capacity and the sanding pattern

are determined mainly by the selection of

the Sand paper (grain size), the speed of the

sanding plate and the application pressure.

ROUGH SANDING

Attach a Sand paper with coarse grain.

Apply only light sanding pressure to achieve

increased material removal.

FINE SANDING

Attach a Sand paper with ﬁne grain. With

moderate pressure, move the machine in a

circular pattern or alternately in lengthwise

and crosswise directions over the work piece.

Do not tilt the machine to avoid sanding

through the work piece (e.g. when sanding

veneer). After ﬁnishing the work, switch off the

machine and lift it from the work piece.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX653 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info