Bedienungsanleitung Worx WX661.1 (Seite 9 von 40) (Englisch)

673279

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Belt sander EN

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for dry sanding–with

high removal capacity–of wood, plastic, metal,

ﬁller as well as varnished surfaces.

1. ON/OFF SWITCH

Depress to start and release to stop your tool.

2. SWITCH LOCK-ON BUTTON

(See Fig. A)

Depress on/off switch (2) then lock on button

(3). Your tool is now locked on for continuous

use. To switch off your tool just depress and

release the on/off switch.

3. VARIABLE SPEED CONTROL DIAL

Adjust the variable speed control (1) to

increase or decrease the speed according to

the material and sanding belt speciﬁcation

to be used (also possible during no load

operation). See the table below for general

guidance on speed selection. Avoid prolonged

use at very low speed as this may damage

your sander’s motor.

Material Speed selection Belt grit

Solid wood 5-6 80

Veneer 2-4 150

Chipboard 1-5 60/80

Plastics 2-5 100

Steel 5-6 80

Paint

removal

6 40/60

Balsa wood 1-3 100

Acrylic 1-2 100

4. CHANGING A SANDING BELT (See Fig. B, C)

WARNING!WARNING! Remove the

main plug from the socket before

changing sanding belt.

Pull the lever (7) to release the belt tension.

Remove and ﬁt a new belt over both rollers.

Ensure the direction of rotation arrows on the

belt and the sander are the same. Close the

lever to tension the belt.

5. BELT CENTERING CONTROL (See Fig. D)

WARNING! Wear eye protection

before carrying out a belt centering

adjustment.

Turn the machine upside down, hold it ﬁrmly

with one hand, start the motor and release the

switch immediately after observing tracking

of sanding belt. If abrasive belt runs outward,

turn tracking adjustment knob counter-

clockwise and clockwise if belt runs inward.

Adjust the belt until the outer edge of the belt

is even with the outer edge of the base-plate

(12). Belt life will be greatly increased by

keeping the tracking adjustment set properly.

6. DUST BAG (See Fig. E)

Always operate your sander with the dust bag

ﬁtted. For the best performance always empty

the dust bag in time. Remove the shaft from

the dust bag and shake out dust. To remove

the bag, slide the mounting bracket out and

away from the sander. To reﬁt the bag, ﬁrmly

push the mounting bracket into the location

on the sander housing.

7. ASSEMBLE THE DUST EXTRACTION

ADAPTER (See Fig. F, G)

Your sander is equipped with two dust

extraction adapters, which are designed for

connecting the hose of a vacuum cleaner.

Insert the 35mm adapter (13a) into the outlet

until it is secured (See F), then insert the 32

mm adapter (13b) into the back of the 35 mm

adapter (Fig. G).

8. DRIVE BELT REPLACEMENT.

WARNING! Remove the main plug

from the socket before carrying out

a drive belt replacement.

Remove the three screws and the belt cover.

Carefully cut the drive belt if not already

broken and remove from your belt sander. Fit

your new drive belt around the large pulley.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX661.1 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info