Bedienungsanleitung Worx WX675.1 (Seite 9 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

575143

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Oscillating Tool EN

OPERATION INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The power tool is intended for sawing and

remodelling wooden materials, plastic,

plaster, non-ferrous metals and fasteners

(e.g. nails and clamps) as well as for working

on soft wall tiles and for dry grinding of small

surfaces. It is especially suitable for working

close to edges and for ﬂush cutting.

1. MOUNTING ACCESSORIES

CAUTION: For all work or when

changing accessories, always wear

protective gloves. Avoid danger of injury

from the sharp edges of the accessories.

Accessories can become very hot while

working, presenting danger of burns! Make

sure the tool is unplugged prior to

changing accessories.

WARNING: To reduce the risk of injury,

do not let the sharp side of the

accessory face back toward the user’s hand.

The tool free system makes you change the

accessories without using an Allen key.

1) For the WORX universal accessories

- Flip the Hyperlock

Accessory Clamping

Lever forward to the open position (See

Fig. A).

- Rotate the Lever counterclockwise to

loosen the Flange (See Fig. B).

- Insert the accessory onto the Universal

Fit

Accessory Interface, then press down

the Flange with ﬁnger to keep blade

temporarily secure (See Fig. B).

- Rotate the Lever clockwise until accessory

is tightened Securely (See Fig. C).

- Flip lever back down (See Fig. C).

- Return lever to seated position

(See Fig. C).

2) For all other branded oscillation tool

accessories (Including original WORX

Sonicrafter) the ﬂange must be

completely removed to use these

accessories (See Fig. D).

2. MOUNTING/CHANGING THE

SANDING SHEET (See Fig. E)

Align the sanding sheet and press it onto the

sanding pad by hand.

Firmly press the power tool with the sanding

sheet against a ﬂat surface and brieﬂy switch

the power tool on. This provides for good

adhesion and prevents premature wear.

If one point has become worn, pull off the

sanding sheet, turn it 120° and place it on

again.

NOTE: For other various brands’ sanding

pad, use small ﬂange provided.

3.MOUNTING THE SUCTION DEVICE

(See Fig. F-J)

When vacuuming, mount the suction device

as shown in F-J.

NOTE: Using the sanding pad perforated. You

can only do the vacuuming after ﬁtting the

dust collector.

4. OPERATING THE ON/OFF SWITCH

To start the machine, push the On/Off switch

forward so that the “I” is indicated on the

switch.

To switch off the machine, push the On/Off

switch toward the rear so that the “0” is

indicated on the switch.

5 USING THE VARIABLE SPEED DIAL

Select oscillation frequency (speed) while the

motor is running.

The Variable Speed Dial can be used to set

the optimum oscillating frequency according

to the accessories used and the respective

application.

High oscillation frequency:

Sawing, rasping and polishing stone and

metal.

Low oscillation frequency:

Sanding, scraping, polishing varnishes.

6. SECURING THE WORKPIECE

CAUTION: Before working with your

tool make sure that no power cords will

be damaged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX675.1 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info