Bedienungsanleitung Worx WX679.11 (Seite 10 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

575119

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Oscillating Tool EN

WORKING HINTS FOR YOUR

TOOL

If your power tool becomes too hot, especially

when used at low speed, set the speed to

maximum and run it with no load for 2-3

minutes to cool the motor. Avoid prolonged

usage at very low speeds. Always keep the

blade sharp.

Always ensure the workpiece is ﬁrmly held or

clamped to prevent movement.

Any movement of the material may affect the

quality of the cutting or sanding ﬁnish.

Start your tool before working and turn it off

only after you stop working.

Do not start sanding without having the

sandpaper ﬁtted.

Do not allow the sandpaper to wear away , it

will damage the sanding pad. The guarantee

does not cover sanding pad wear and tear.

Use coarse grit paper to sand rough surfaces,

medium grit for smooth surfaces and ﬁne grit

for ﬁnishing surfaces. If necessary, ﬁrst make

a test run on scrap material.

Excessive force will reduce the working

efﬁciency and cause motor overload.

Replacing the accessory regularly will

maintain optimum working efﬁciency.

MAINTAIN TOOLS WITH

CARE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

Your power tool requires no additional

lubrication or maintenance. There are no

user serviceable parts in your power tool.

Never use water or chemical cleaners to clean

your power tool. Wipe clean with a dry cloth.

Always store your power tool in a dry place.

Keep the motor ventilation slots clean. Keep

all working controls free of dust. Occasionally

you may see sparks through the ventilation

slots. This is normal and will not damage your

power tool.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or similarly qualiﬁed persons in order to

avoid a hazard.

PLUG REPLACEMENT

(UK & IRELAND ONLY)

If you need to replace the ﬁtted plug then

followthe instructions below.

IMPORTANT

The wires in the mains lead are colored in

accordance with the following code:

blue – neutral

brown – live

As the colors of the wires in the mains lead

of thisappliance may not correspond with the

coloured markings identifying the terminals

in your plug,proceed as follows. The wire

which is coloured blue must be connected to

the terminal which is marked with N. The wire

which is coloured brown must be connected

to the terminal which is marked with L.

WARNING: Never connect live or

neutral wires to the earth terminal of the

plug. Only ﬁt an approved 13A BS1363/A

plug and the correct rated fuse.

NOTE: If a moulded plug is ﬁtted and has to

be removed take great care in disposing of the

plug and severed cable, it must be destroyed

to prevent engaging into a socket.

Connect

Blue to N

(neutral)

Outer sleeve

firmly clamped

Cable grip

Brown L (live)

13 Amp fuse approved

to BS1362

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX679.11 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info