Bedienungsanleitung Worx WX700 (Seite 10 von 120) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

575106

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Angle grinder EN

1110

carrying it at your side. Accidental

contact with the spinning accessory could

snag your clothing, pulling the accessory

into your body.

14. Regularly clean the power tool’s air

vents. The motor’s fan will draw the

dust inside the housing and excessive

accumulation of powdered metal may

cause electrical hazards.

15.Do not operate the power tool near

ﬂammable materials. Sparks could

ignite these materials.

16. Do not use accessories that require

liquid coolants. Using water or other

liquid coolants may result in electrocution

or shock.

17.Your hand must hold on the handle

when you are working. Always use the

auxiliary handles supplied with the tool.

Loss of control can cause personal injury

FURTHER SAFETY INSTRUCTIONS FOR

ALL OPERATIONS

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush

or any other accessory. Pinching or snagging

causes rapid stalling of the rotating accessory

which in turn causes the uncontrolled power

tool to be forced in the direction opposite of

the accessory’s rotation at the point of the

binding.

For example, if an abrasive wheel is snagged

or pinched by the workpiece, the edge of the

wheel that is entering into the pinch point can

dig into the surface of the material causing

the wheel to climb out or kick out. The wheel

may either jump toward or away from the

operator, depending on direction of the

wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse

and/or incorrect operating procedures or

conditions and can be avoided by taking

proper precautions as given below.

1. Maintain a ﬁrm grip on the power

tool and position your body and

arm to allow you to resist kickback

forces. Always use auxiliary handle, if

provided, for maximum control over

kickback or torque reaction during

start-up. The operator can control torque

reactions or kickback forces, if proper

precautions are taken.

2. Never place your hand near the

rotating accessory. Accessory may

kickback over your hand.

3. Do not position your body in the

area where power tool will move if

kickback occurs. Kickback will propel

the tool in direction opposite to the wheel’s

movement at the point of snagging.

4. Use special care when working

corners, sharp edges etc. Avoid

bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory

and cause loss of control or kickback.

5. Do not attach a saw chain

woodcarving blade or toothed saw

blade. Such blades create frequent

kickback and loss of control.

ADDITIONAL SAFETY INSTRUCTIONS

FOR GRINDING AND CUTTING-OFF

OPERATIONS

SAFETY WARNINGS SPECIFIC FOR

GRINDING AND ABRASIVE CUTTING-

OFF OPERATIONS:

1. Use only wheel types that are

recommended for your power tool

and the speciﬁc guard designed for

the selected wheel. Wheels for which

the power tool was not designed cannot be

adequately guarded and are unsafe.

2. The grinding surface of centre

depressed wheels must be mounted

below the plane of the guard lip. An

improperly mounted wheel that projects

through the plane of the guard lip cannot

be adequately protected.

3. The guard must be securely attached

to the power tool and positioned

for maximum safety, so the least

amount of wheel is exposed towards

the operator. The guard helps to protect

operator from broken wheel fragments and

accidental contact with wheel.

4. Wheels must be used only for

recommended applications. For

example: do not grind with the side

of cut-off wheel. Abrasive cut-off wheels

are intended for peripheral grinding, side

forces applied to these wheels may cause

them to shatter.

5. Always use undamaged wheel ﬂanges

that are of correct size and shape

for your selected wheel. Proper wheel

ﬂanges support the wheel thus reducing

the possibility of wheel breakage. Flanges

for cut-off wheels may be different from

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX700 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info