Bedienungsanleitung Worx WX702.2 (Seite 12 von 120) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

575112

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Angle grinder EN

1312

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for cutting,

roughing and brushing metal and stone

materials without using water. For cutting

metal, a special protection guard for cutting

(accessory) must be used.

1. INSTALLING THE AUXILIARY HANDLE

(See Fig. A)

You have the option of two working positions

to provide the safest and most comfortable

control of your angle grinder. The handle is

screwed clockwise into either hole on the sides

of the gear case.

Anti-vibration auxiliary handle

(WX707 WX707.1)

The anti-vibration auxiliary handle reduces

the vibrations, making operation more

comfortable and secure.

2. ADJUSTING WHEEL GUARD (See Fig. B)

Before any work on the machine itself,

pull the mains plug.

For work with grinding or cutting discs,

the wheel guard must be mounted.

Wheel Guard for Grinding

The coded projection on the wheel guard (10)

ensures that only a guard that ﬁts the machine

type can be mounted.

Open the clamping lever (9). Place the wheel

guard (10) with coded projection into the

coded groove on the spindle of the machine

head and rotate to the required position

(working position).

To fasten the wheel guard (10), close the

clamping lever (9).

The closed side of the wheel guard (10)

must always point to the operator.

NOTE: With the clamping lever (9) open the

clamp adjusting nut (7) can be adjusted to

ensure the guard is securely clamped after the

clamping lever (9) is ﬁnally closed.

Wheel Guard for Cutting

ARNING! For cutting metal,always

work with the wheel guard for cutting(12).

The wheel guard for cutting (12) is mounted

in the same manner as the wheel guard for

grinding(10) .

3. SPINDLE LOCK BUTTON

Clean the grinder spindle and all parts to be

mounted. For clamping and loosening the

grinding tools, lock the grinder spindle with

the spindle lock button.

Actuate the spindle lock button only when the

grinder spindle is at a standstill!

4. FITTING THE DISCS (See Fig. C1, C2, C3)

Put the inner ﬂange onto the tool spindle. Ensure it

is located on the two ﬂats of spindle (See Fig. C1).

Place the disc on the tool spindle and inner

ﬂ

ange. Ensure it is correctly located. Fit the

threaded outer ﬂange making sure it is facing in

the correct direction for the type of disc ﬁtted.

For grinding discs, the ﬂange is ﬁtted with the

raised portion facing towards the disc. For

cutting discs, the ﬂange is ﬁtted with the raised

portion facing away from the disc (See Fig. C2).

Press in the spindle lock button and rotate the

spindle by hand until it is locked. Keeping the

lock button pressed in, tighten the outer ﬂange

with the spanner provided. (See Fig. C3)

USING INSTALOCK

TOOL-LESS FLANGE

(WX701.2 WX702.1 WX707.1)

Lock the grinder spindle with the spindle lock

button. To tighten the INSTALOCK

tool-less

Flange (13) ﬁrmly turn the grinding disc in

clockwise direction.

A properly attached, undamaged INSTALOCK

tool-less Flange can be loosened by hand

when turning the knurled ring in anti-clockwise

direction. Never loosen a tight INSTALOCK

tool-less Flange with pliers. Always use the

two-pin spanner.

5. SLIDE ON/OFF SWITCH (See Fig. D)

To start the power tool, push the on/off switch

(2) forward.

To lock the on/off switch (2), press the on/off

switch (2) down at the front until it engages.

To switch off the power tool, release the on/

off switch (2) or, if it is locked, brieﬂy push

down the back of the on/off switch (2) and then

release it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX702.2 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info