Bedienungsanleitung Worx WX800.9 (Seite 8 von 12) (Englisch)

673105

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

WX800 WX800.9

Lithium-Ion cordless

angle grinder

coolants.

Using water or other liquid coolants may

result in electrocution or shock.

p) Your hand must hold on the handle when you are

working. Always use the auxiliary handles supplied

with the tool. Loss of control can cause personal injury.

FURTHER SAFETY INSTRUCTIONS FOR ALL

OPERATIONS

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in

the direction opposite of the accessory’s rotation at

the point of the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward

or away from the operator, depending on direction

of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can

be avoided by taking proper precautions as given

below.

a) Maintain a ﬁrm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control

over kickback or torque reaction during

start-up. The operator can control torque

reactions or kickback forces, if proper precautions

are taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over your

hand.

c) Do not position your body in the area

where power tool will move if kickback

occurs. Kickback will propel the tool in direction

opposite to the wheel’s movement at the point of

snagging.

d) Use special care when working corners,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp edges

or bouncing have a tendency to snag the rotating

accessory and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades

create frequent kickback and loss of control.

ADDITIONAL SAFETY INSTRUCTIONS FOR

GRINDING AND CUTTING-OFF OPERATIONS

Safety Warnings Specific for Grinding and

Abrasive Cutting-Off Operations:

a) Use only wheel types that are

recommended for your power tool and the

speciﬁc guard designed for the selected

wheel.

Wheels for which the power tool was not

designed cannot be adequately guarded and are

unsafe.

b) The grinding surface of centre depressed

wheels must be mounted below the plane

of the guard lip.

An improperly mounted wheel

that projects through the plane of the guard lip cannot

be adequately protected.

c) The guard must be securely attached

to the power tool and positioned for

maximum safety, so the least amount of

wheel is exposed towards the operator.

The guard helps to protect the operator from broken

wheel fragments, accidental contact with wheel and

sparks that could ignite clothing.

d) Wheels must be used only for

recommended applications. For example:

do not grind with the side of cut-off wheel.

Abrasive cut-off wheels are intended for peripheral

grinding, side forces applied to these wheels may

cause them to shatter.

e) Always use undamaged wheel ﬂanges

that are of correct size and shape for your

selected wheel.

Proper wheel ﬂanges support the

wheel thus reducing the possibility of wheel breakage.

Flanges for cut-off wheels may be different from

grinding wheel ﬂanges.

f) Do not use worn down wheels from larger

power tools.

Wheel intended for larger power tool

is not suitable for the higher speed of a smaller tool

and may burst.

ADDITIONAL SAFETY WARNINGS SPECIFIC

FOR ABRASIVE CUTTING-OFF OPERATIONS:

a) Do not “jam” the cut-off wheel or apply

excessive pressure. Do not attempt

to make an excessive depth of cut.

Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the

cut and the possibility of kickback or wheel breakage.

b) Do not position your body in line with and

behind the rotating wheel.

When the wheel,

at the point of operation, is moving away from your

body, the possible kickback may propel the spinning

wheel and the power tool directly at you.

c) When wheel is binding or when

interrupting a cut for any reason, switch

off the power tool and hold the power tool

motionless until the wheel comes to a

complete stop. Never attempt to remove

the cut-off wheel from the cut while the

wheel is in motion otherwise kickback

may occur.

Investigate and take corrective action to

eliminate the cause of wheel binding.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed

and carefully re-enter the cut.

The wheel may

bind, walk up or kickback if the power tool is restarted

in the workpiece.

e) Support panels or any oversized workpiece

to minimize the risk of wheel pinching and

kickback. Large workpieces tend to sag

under their own weight.

Supports must be

placed under the workpiece near the line of cut and

near the edge of the workpiece on both sides of the

wheel.

Use extra caution when making a “pocket

Worx WX800.9 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Worx WX800.9

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info