Bedienungsanleitung Worx WX800 (Seite 7 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

673104

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENLithium-Ion cordless angle grinder

Auxiliary handle 1 1

2.0Ah Battery(WA3551.1) 2 /

1hr Charger (WA3860) 1 /

We recommend that you purchase your accessories

from the same store that sold you the tool. Refer to

the accessory packaging for further details. Store

personnel can assist you and offer advice.

SAFETY INSTRUCTIONS

FOR ALL OPERATIONS

SAFETY WARNINGS COMMON FOR GRINDING

OR ABRASIVE CUTTING-OFF OPERATIONS:

a) This power tool is intended to function as

a grinder or cut-off tool. Read all safety

warnings, instructions, illustrations and

speciﬁcations provided with this power

tool.

Failure to follow all instructions listed below

may result in electric shock, ﬁre and/or serious injury.

b) Operations such as sanding, wire brushing,

polishing are not recommended to be

performed with this power tool.

Operations

for which the power tool was not designed may create

a hazard and cause personal injury.

c) Do not use accessories which are not

speciﬁcally designed and recommended

by the tool manufacturer.

Just because the

accessory can be attached to your power tool, it does

not assure safe operation.

d) The rated speed of the accessory must

be at least equal to the maximum speed

marked on the power tool.

Accessories running

faster than their rated speed can break and ﬂy apart.

e) The outside diameter and the thickness

of your accessory must be within the

capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately

guarded or controlled.

f) Threaded mounting of accessories must

match the grinder spindle thread. For

accessories mounted by ﬂanges, the

arbour hole of the accessory must ﬁt the

locating diameter of the ﬂange.

Accessories

that do not match the mounting hardware of the

power tool will run out of balance, vibrate excessively

and may cause loss of control.

g) Do not use a damaged accessory. Before

each use inspect the accessory such as

abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess

wear. If power tool or accessory is

dropped, inspect for damage or install an

undamaged accessory. After inspecting

and installing an accessory, position

yourself and bystanders away from the

plane of the rotating accessory and run the

power tool at maximum no-load speed for

one minute.

Damaged accessories will normally

break apart during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments.

The eye protection must

be capable of stopping ﬂying debris generated by

various operations . The dust mask or respirator must

be capable of ﬁltrating particles generated by your

operation. Prolonged exposure to high intensity noise

may cause hearing loss.

i) Keep bystanders a safe distance away

from work area. Anyone entering the

work area must wear personal protective

equipment.

Fragments of workpiece or of a broken

accessory may ﬂy away and cause injury beyond

immediate area of operation.

j) Hold the power tool by insulated gripping

surfaces only, when performing an

operation where the cutting tool may

contact hidden wiring.

Contact with a “live” wire

will also make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

k) Never lay the power tool down until the

accessory has come to a complete stop.

The spinning accessory may grab the surface and pull

the power tool out of your control.

l) Do not run the power tool while carrying it

at your side.

Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

m) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal may

cause electrical hazards.

n) Do not operate the power tool near

ﬂammable materials.

Sparks could ignite these

materials.

o) Do not use accessories that require liquid

coolants.

Using water or other liquid coolants may

result in electrocution or shock.

p) Your hand must hold on the handle when you are

working. Always use the auxiliary handles supplied

with the tool. Loss of control can cause personal injury.

FURTHER SAFETY

INSTRUCTIONS FOR ALL

OPERATIONS

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in

the direction opposite of the accessory’s rotation at

the point of the binding.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WX800 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Worx WX800

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info