Bedienungsanleitung Xerox WorkCentre 5855 (Seite 72 von 702) (Englisch)

610816

Zoom out

Zoom in

Vorherige Seite

1/702

Nächste Seite

Copy WorkCentre

5845/5855/5865/5875/5890

70 User Guide

Use the No Finishing option if no finishing is required for the output.

Use the collation options to sort your copies into sets (1,2,3 1,2,3 1,2,3) or stacks (1,1,1 2,2,2

3,3,3).

Use the stapling options to staple your document. The options available are dependent on the

finishing device installed. The basic stapling options are Off, 1 Staple, 2 Staples and Multi-Staple.

Use the Hole Punched / Stapled option if you want your output to be hole punched or hole punched

and stapled. Each sheet will be punched individually so there is no limit to the number of pages you

can have in a set. Hole punching can only be selected for A4 LEF (8.5 x 11" LEF) and A3 (11 x 17”)

paper.

Note: The Collation options must be set before selecting the Hole Punched / Stapled options.

Note: SEF is Short Edge Feed (where the short edge of the paper is the leading edge when the paper

is fed into the device). LEF is Long Edge Feed (where the paper is oriented so that the long edge is

fed into the device first).

Use the Booklet options to automatically produce folded and stapled booklets. A cover can be

inserted onto the booklet automatically.

Use the Booklet Creation option to automatically reduce and arrange the images in the correct

sequence on your selected media, so that a booklet is created when the copy set is folded in half.

Use the Folding options to fold a single sheet of A4 (8.5 x 11”) media in a weight range of 60 to

120 gsm (16 to 32 lb). Pages can be tri-folded in a C fold or Z fold .

1. Load your documents face up in the document feeder input tray. Adjust the guide to just touch

the documents.

Lift up the document feeder. Place the document face down onto the document glass and

2. Press the Clear All button on the control panel to cancel any previous programming selections.

3. Press the Services Home button.

4. Select the Copy button on the touch screen. The copy features are displayed.

5. If required, select the Copy tab. This is usually the active tab when the Copy service opens.

6. If required, select the More... button at the bottom of the Copy Output section to access all the

finishing options. The number of options displayed will depend upon the finishing device and

kits installed (there may not be enough to require a More... button).

7. Select the Copy Output option required.

•None

•Collation

•Stapled

• Hole Punched / Stapled

• Booklet

•Tri-Folded

8. Select the OK button.

9. Enter the number of prints required using the numeric keypad on the control panel.

10. Press the Start button on the control panel to scan the original.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Xerox WorkCentre 5855 Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Xerox WorkCentre 5855

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info