578076
1
Zoom out
Zoom in
INSTALLATION/OWNER’S MANUAL
DVD Navigation system with 7” Touch Screen Display
XM-VRSUN728
-4-
-5- -6-
-7-
1. Power on/off
2. Band switching/Receiving or dial a call
3. EQ setting
4. Previous track
5. Next track
6. Mute
7. Mode switching from radio, SD, USB,AUX IN,
Bluetooth, GPS navigation
8. Diming of the display panel
9. GPS navigation
10. Adjust the angle up of the display panel
11. Open the display panel
12. Adjust the angle down of the display panel
13. USB slot
14. SD slot
15. GPS card slot
16. AUX IN jack
17. Volume up/down, SELECT key
18. IR sensor
19. Microphone
1. Enter the dial keyboard interface
2. Phonebook searching function
3. Display the phonebook
4. Bluetooth music interface
5. Back to main interface
6. Setting interface
7. Back to previous page
Replace the Battery
When the operational range of the remote control becomes short or non-functional, replace battery with a
new CR2025 battery. Check the battery polarity before replacement.
Replace the Battery of IR Handset
Notes on installationContents
-3-
Control Panel Layout Remote Control Layout Wiring Diagram General Function
-8-
-9-
-11-
TUNING UP and DOWN
Short press this icon one time to adjust the current frequency up/down automatically. It will stop searching
after the strongest station has been tuned.
Long press, station will be searched for manually lower or higher by 0.05MHZ each time.
RDS Function
Select the RDS function in the radio interface: AF, TA, PTY. You can turn on/off by click these function
keys. The icons will display in the screen if you have selected
AF: Alternative frequencies
It will adjust to the strongest signal frequency for the same station automatically, when the car is being
driven from one area to another.
TA: Traffic anouncement Function
When it receives traffic announcement, it will display the contents on screen. When the Traffic
announcement is over, it will go back to the former playing mode.
PTY: Program Type code
Content of program such as news, light music, sports etc.
STEREO/MONO
Select ST to enter stereo sound, select mono to enter mono sound.
VOL UP/VOL DOWN
Turn the knob to the left side, the volume will be decreased.
Turn the knob to the right side, the volume will be increased.
LED COLOR SETTING
Click the light icon to enter LED light setting:
AUTO/GREENB/BLUE/RED/YELLOW/CYAN/PURPLE/WHITE
USB/SD PLAYING
Click the different type of file on the left side to display the folder/music/video/picture.
POWER ON/OFF
Long press the power key to turn on/off the unit.
MUTE
Press this key to make the audio silence, press again to resume the sound.
Searching function
Short press this key, it will automatically scan the preset radio station.
Long press this key, it will search all the frequency, and save the radio station.
Sliding the 3 pages, you can enter the preset stations by short press or stored the present frequency in the
bar by long press.
LOCAL/DISTANCE
Short pressing this icon to enter the LOC/DX setting menu, it will search the strong signal of local, click
again to return the distance mode.
BAND
Press BAND button to switch the band from FM1, FM2, FM3, AM1, AM2.
-17-
Install the unit (DIN front mount)
-18-
DIN FRONT-MOUNT (method A)
DIN REAR MOUNT(method B)
Install and Remove the Front Panelnot available for this
unit(fixed panel)
-16-
-2-
Note on installation -------------------------------------------------------- 3
Precautions ------------------------------------------------------------------ 4
Control Panel Layout ------------------------------------------------------ 4
Remote Control Layout --------------------------------------------------- 5
Wiring Diagram ------------------------------------------------------------- 6
Ganeral Function ---------------------------------------------------------- 7
Bluetooth Operation------------------------------------------------------- 11
Setting Menu --------------------------------------------------------------- 12
Replace the Battery of IR Handset ----------------------------------- 16
Install the unit -------------------------------------------------------------- 17
The unit is designed for 12V DC, negative ground operation systems only. Before installing the unit, make
sure your vehicle is connected to 12V DC negative grounded electrical system.
The negative battery terminal must be disconnected before making connections which can prevent damage
to the unit from short circuiting.
Be sure to connect the correct speaker to the correct terminal. Never connect the left and right channel
speaker cables to each other or to the vehicle body. Do not block vents or radiator panels. Doing so will
cause heat to build up and may result in fire.
After completion of installation and replacement of battery, press the reset button on the front panel with a
pointed object (such as a ball point pen) to set the unit to its initial status.
Installing the Unit
1. Dashboard
2. Holder
After inserting the holder into the dasrwhboard, select
the appropriate tab according to the thickness of the
dashboard material and bend them inwards to secure
the holder in place.
3. Screw
1. Dashboard
2. Nut (5mm)
3. Plan washer
4. Screw (5*25mm)
5. Screw
6. Starp be sure to use the starp to secure the back of
the unit in place.The starp can be bent by hand to the
desired angle.
7. Plain Washer
Remove the Unit
1. Frame
2. Insert fingers into the groove in the front of frame and
pull out to remove the frame. (When reattaching the
frame,point the side with a groove downwards and
attach it).
3. Lever
Insert the levers supplied with the unit into the grooves
at both sides of the unit as shown in figure until they
click. Pulling the levers makes it possible to remove the
unit from the dashboard.
Installation using the screw holes on the sides of the
Unit.
Fastening the unit to the factory radio mounting
bracket.
1. Select a position where the screw holes of the bracket
and the screw holes of the main unit become aligned
(are fitted) and tighten the screw at 2 places on each
side.Use either truss screws (5*5 mm) or flush surface
screw (4*5 mm).
2. Screw(“T”Position).
3. Dashboard or Console.
Note: The mounting box,outer trim ring,and half-sleeve
are not used for method B installation.
Pull out the battery holder while pressing the stopper 1.
Place battery whth (+) mark facing up into the battery
holder.
Insert the battery holder into the remote controller.
Remove the front panel
Press “REL” button in the panel , pull out the A, then
slightly pull out B
Please see picture on the left
Install the front panel
Put notch B (shown as picture) onto buckle B, and then
slightly press A into the left side.
Note: Please don’t insert finger in control panel. If
connector is dirty, use a clean soft cloth to wipe it clean.
1. Power on/off
2. MODE
3. PLAY/PAUSE
4. MUTE
5. TITLE
6. SUB-T
7. RIGHT
8. SETUP
9. ANGLE
10. SLOW
11. VOL+
12. ZOOM
13. SEL
14. SEEK+//PREVIOUS
TRACK/TUNING UP
15. VOL-
16. AUDIO
17. Number keys
18. GOTO
19. PBC
20. OSD
21. LOC RDM
22. SEEK-/PREVIOUS
TRACK/TUNING DOWN
23. AMS/REPEAT
24. ST/PROG
25. STOP/BACK
26. DOWN
27. LEFT
28. ENTER
29. BAND
30. UP
1. GPS navigation
2. Radio
3. Disc(No disc function in this unit )
4. Bluetooth
5. TV(NO TV function in this unit)
6. AV-IN 1
7. USB
8. SD
9. Main Interface display switching
10.Close the display
11.Sourcing indicator: Disc, USB, SD, Bluetooth
12.Time indicator
13.Camera input(camera is not included in
this unit)
14.Setting menu
15.Wallpaper switching
16.Compass
17.Counter
18.Gamer center
19.AV-IN 2
20.Volume indicator
BAND
ST
PROG
AMS
PRT
LOC
RDM
TITLE
MODEPOW MUTE
SUB-T
ENTER
SEEK- SEEK+
SEL
PBC
1 2 3 4
5 6 7 8
9 10 10+
GOTO
VOL- AUDIOOSD
SETUP
VOL+ ZOOM
SLOWANGLE
1 2
3 4
9
10
11
12
13
14
15
16
18
5
6
7
8
17
19
20
21
22
23
24
25
26
27
28
29
30
11
12
13
15
14
16
18
1917
11
12
13
14 15
20
16
19
18
17
SETTING MENU
PREPARE FOR BLUETOOTH OPERATION
(1) When use Bluetooth, please make sure the mobile phone supports Bluetooth function.
(2) For the different kind of mobile phone, Bluetooth emissive power has some difference. To get the
best conversation quality, it is commended that the distance between the mobile phone and the unit is
within 3m. And please don’t put any metal object or any obstacle between the path of the mobile
phone and the unit.
PAIRING
1) On the mobile phone, select the Bluetooth set up. (Please refer to the instruction manual of your
mobile phone on how to operate Bluetooth.
2) “MT36” should appear in the list on your mobile phone, please select “MT36” and then input
password “0000” .
3) When successful paired, “MT36” will be displayed on LCD.
BLUETOOTH AUDIO (A2DP FUNCTION)
The unit supports Bluetooth audio function. If your mobile phone can play stereo audio, when the
paring is ok, you can choose the unit you have paired to play the stereo music. button on the
front panel of the unit serves as PAUSE/PLAY control button. (It is up to the mobile phone, the
different mobile phone has the different define.)
Use button on the front panel of the unit to choose the previous/next track. (It is up to the
mobile phone, the different mobile phone has the different define.) Note: when playing music, you can
not make any phone call. When there is an incoming call, you can choose to answer it or not.
1. Time setting
A B
A B
XM-VRSUN728 XM-VRSUN728
XM-VRSUN728
XM-VRSUN728
XM-VRSUN728
XM-VRSUN728
-10-
BLUETOOTH OPERATION
XM-VRSUN728
-13-
XM-VRSUN728
-14-
XM-VRSUN728
-12-
XM-VRSUN728
XM-VRSUN728
-15-
XM-VRSUN728
XM-VRSUN728
XM-VRSUN728
XM-VRSUN728 XM-VRSUN728 XM-VRSUN728
D-T V
A-T V
G PS
R ADIO ANT
F R ONT L O UT P UT (WHIT E )
F R ONT R O UT P UT (R E D)
R E A R L O UTP UT (WHIT E )
R E A R R O UT PUT(R E D)
AUX L I NP UT (WHIT E )
AUX R I NP UT (R E D)
AUX V IDE O I NP UT (Y E L L OW)
VIDE O O UT P UT (Y E L L OW)
C AME R A INP UT (Y E L L OW)
S UB WOOF E R O UTP UT (G R E E N)
S P E A K E R R E AR R +
S P E A K E R R E AR R -
S P E A K E R F R ONT R +
S P E A K E R F R ONT R -
S P E A K E R F R ONT L -
S P E A K E R F R ONT L +
S P E A K E R R E AR L -
S P E A K E R R E AR L +
ANT C ONTR OL
G R OUND
B L A C K
WHITE
WHIT E /B L AC K
G R E E N/B L A C K
G R E E N
VIOL E T
VIOL E T/B L A C K
B L UE /WHIT E
G R AY /B L A C K
G R AY
B L UE
PAR K ING
C OF F E E
B AC K
P INK
OR A NG E /WHITE
K E Y1
K E Y2
AC C
C OF F E E /B L AC K
R E D
B +
Y E L L OW
2. GPS Path setting
Select the EXE file in the GPS card.
3. Back ground setting
5. General Setting
1. Turn on/off the power by pressed any key
2. Turn on/off the warning when the car is running.
3. Turn on/off the GPS monitor, while the GPS is running, other source can play at the same time.
4. Calibration of the touch panel
5. Language setting
6. STEERING WHEEL CONTROL
Enter the setting menu, click the STEER icon to enter steering wheel setting, following the steps which
notice on the screen.
4. Sound Setting
Turn on/off the Touching sound
Turn on/off Back car volume
Turn on/off user defaults volume
Turn on/off GPS MIX: display the music/radio/sound in the GPS interface at the same time while GPS
is running
Report point remove mute: turn on/off GPS sound mute
Bluetooth sound setting
5. EQ SETTING
Press EQ or Setting -sound setting to select:
FLAT/CLASSIC/POP/ROCK/JAZZ/BASS/TREBLE/BALANCE/FADER/LOUD

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Xomax XM-VRSUN728 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Xomax XM-VRSUN728

Xomax XM-VRSUN728 Installationsanweisung - Deutsch - 42 seiten

Xomax XM-VRSUN728 Bedienungsanleitung - Deutsch - 59 seiten

Xomax XM-VRSUN728 Installationsanweisung - Englisch - 42 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info