Bedienungsanleitung Xoro HTL2446 (Seite 26 von 30) (Englisch)

678114

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

English

For the column of the tuning following configuration options are available:

LNB Typ define the oscillator frequency for your LNB . Please take the correct value from the

manual of your LNB (standard:09750/10600)

LNB Voltage This parameter defines the storm voltage of the antenna, and signal from horizontal

or vertical polarized transponder will be received. The setting will only have to be

changed in very rare cases. A false setting will result in missing program or no signal

reception at all. (standard: On)

22KHz The receiver can switch the LNB with 22 KHz signals for the reception of another

frequency band. The setting will only have to be changed in very rare cases. A false

setting will result in missing program or no signal reception at all. (standard: Auto)

Toneburst Tone burst switcher has two input ports, enabling the connection of 2 antennas or

LNB to the receiver. If you have a Tone burst switcher, you will have to select one of

the both connections (A or B) for the satellite chosen on the left side.

DiSEqC DiSEqC switcher has up to 16 input ports enabling the connection of multiple anten

nas or LNB to the receiver. If you have a DiSEqC switcher, you will have to select one

of connections for the satellite chosen on the left side. Please check which version

(1.0, 1.1) could be supported in the manual of your switcher.

Motor Rotatable Antennas require extended configurations. We recommend professional

installation from a technician. Please set up according to your antenna.

Use a Unicable reception system, please proceed as follows:

 Navigate in the manual tuning to the right column to the menu item LNB type and press the

OK button.

 Select from the list at the bottom of the option Unicable and press the OK button to make

further adjustments to your Unicable reception system:

LNB high / low Define the frequency range for your Unicable LNB. No changes need

to be made here normally.

User ID Each receiver in a single-cable reception system must be assigned a

user ID. Most systems are designed for 4 or 8 receivers. It is im

portant to ensure that only one receiver is assigned a user tape. Uses

more than one receiver, the same user ID, it comes to function

disorders. Other, incorrectly Receiver can cause the reception of the

equipment is impaired.

Frequenz Each user band is a frequency band associated with that you must

set in this menu item, each user on each band.

Notes:

 Please ask the installer of your reception system, which are user band and what frequency

band available to you. In the documents relating to your reception system, this information

should be also be found.

 Note that all components of your receiving system for the cable system must be compatible.

Main menu

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Xoro HTL2446 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Xoro HTL2446

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info