Bedienungsanleitung Xterra TR6.65 TREADMILL (Seite 22 von 24) (Englisch)

587185

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

TR6.55 Treadmill

BELT / DECK LUBRICATION:

Do not lubricate with other than Xterra approved lubricant. Your treadmill comes with one tube of

lubricant and extra tubes can be ordered directly from Xterra. There are commercially available

lube kits, but the only one currently approved by Xterra is Lube-N-Walk. These kits come with an

application wand that makes applying the lubrication easier. The kits can be purchased from

Xterra.

Keeping the deck lubricated at the recommended intervals ensures the longest life possible for

your treadmill. If the lubricant dries out, the friction between the belt and deck rises and places

undue stress on the drive motor, drive belt and electronic motor control board, which could result

in catastrophic failure of these expensive components. Failure to lubricate the deck at regular

intervals may void the warranty.

The deck comes pre-lubricated and subsequent lubrication should be performed every 180 hours

of use. The console has a built in lubrication reminder indicator that lights every 180 hours of use.

To lubricate the deck with the tube of lubricant supplied it will be necessary to loosen the walking

belt. Using the 6 mm allen wrench supplied, loosen the two rear roller adjustment bolts -- located

in the rear end caps – enough to get your hand under the belt (5 –10 turns). Make sure to loosen

both bolts the same amount of turns and also remember how many turns, because when finished

you will need to tighten the bolts back to the point they were before.

Once the belt is loose, wipe the deck with a clean lint free cloth to remove any dirt. Apply the

whole tube of lubricant onto the deck surface about 18 inches from the motor cover. Squeeze out

the contents of the tube across the deck (parallel to the motor cover) in about a one-foot long line,

like toothpaste on a toothbrush. The one-foot line should be in the middle of the deck at

approximately equal distance from both side edges of the belt. You want the lubricant to be

applied about the spot that your feet would hit the belt as you are walking. This should be about

18 inches from the motor cover, but you may want to walk on the treadmill before loosening the

belt to note where your feet land on the belt. If you mostly run on the treadmill, the spot where

your feet land may be different from walking.

Once the lubricant is applied, tighten the rear roller bolts the same amount of turns as when you

loosened them. Run the treadmill at about 6 mph without walking on it for about a minute or two

to make sure the belt stays in the middle of the deck. If the belt tracks to one side then follow the

belt tracking instructions to remedy. Now the deck is lubricated and you should walk, not run, on

the treadmill immediately for at least 5 minutes to ensure the lubricant is evenly distributed. If you

purchase a Lube-N-Walk kit, follow the instructions that come with it to apply the lubrication.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Xterra TR6.65 TREADMILL Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info