587187
12
Zoom out
Zoom in
Vorherige Seite
1/15
Nächste Seite
20
TR600 Treadmill
TR600 Treadmill
21
The treadmill is designed so that the tread-belt remains reasonably centered while in use. It
is normal for some belts to drift near one side while in use, depending on a user’s gait and if
they favor one leg. But if during use the belt continues to move toward one side, adjustments
are necessary.
SETTING TREAD-BELT TRACKING
An 6mm Allen wrench is provided for this adjustment. Make tracking adjustments on the left
side bolt. Set belt speed at 3 mph. Be aware that a small adjustment can make a dramatic
difference which may not be apparent right away.
If the belt is too close to the left side, then turn
the bolt only a 1/4 turn to the right (clockwise) and
wait a few minutes for the belt to adjust itself.
Continue to make 1/4 turns until the belt
stabilizes in the center of the running deck.
If the belt is too close to the right side, turn the
bolt counter-clockwise. The belt may require
periodic tracking adjustment depending on use
and walking/running characteristics. Some users may affect tracking differently. Expect to
make adjustments as required to center the tread-belt. Adjustments will become less of a
maintenance concern as the belt is used. Proper belt tracking is an owner responsibility
common with all treadmills.
ATTENTION
Damage to the running belt resulting from improper tracking / tension adjustments is not
covered under the XTERRA Fitness warranty.
Treadbelt Tracking Adjustment
Belt/Deck Lubrication Procedure
First, you want to clean between the belt and deck to remove any debris that may be trapped.
Use a clean, non-fraying rag, t-shirt, or light towel. Halfway between the end of the treadmill
and motor cover, shove the garment under the belt until you can grasp it on both sides of the
belt. Drag the garment the length of the entire belt 1-2 times. Remove the garment.
Do not lubricate with anything other than XTERRA Fitness approved lubricant. Your treadmill
comes with one tube of “Lube” and extra tubes can be ordered directly from
www.xterratness.com.
Keeping the deck lubricated at the recommended intervals ensures the longest life possible
for your treadmill. If the lubricant dries out, the friction between the belt and deck rises and
places undue stress on the drive motor, drive belt and electronic motor control board, which
could result in failure of these components. Failure to lubricate the deck at regular intervals
may void the warranty.
The belt & deck come pre-lubricated and subsequent lubrication should be performed every
90 hours of use or if you notice that the deck is dry. It is recommended that you reach be-
tween the belt and deck to verify there is lubrication present, every other month. If you check
and there isn’t any lubrication present, follow the procedure below even though the “Lube”
indicator isn’t lit on the console. Otherwise, lubricate when the console’s lubrication reminder
lights after 90 hours of use. Use the following procedure to apply the silicone lubricant:
1. Turn the power switch off and unplug the power cord from the wall outlet
2. Measure 18” from the edge of the motor cover; kneel down and reach under the belt
approximately 4- 6” from one edge. Squirt a line of lubricant about 1/8” wide x 15” long
in an “S” pattern perpendicular to the motor cover.
3. Repeat the process on the opposite side.
4. Plug the electrical cord back into the outlet and turn the power switch on.
5. Walk on the belt at a moderate speed for ve minutes to evenly distribute the silicone
lube.
6. Note: If the “Lube” message appears on the console, perform the following procedure to
reset the message:
1. To enter the Engineering Mode Menu press and hold down the Start, Stop and
Enter keys, then at the same time insert the safety key. Keep holding the keys down
until the Display displays Engineering Mode Menu. Press the Enter key to access
2. Press the Speed 5 key (or Speed 6 key to go backwards) until “Functions”
appears; press Enter
3. Press the Speed 5 key until “Reset Lube” message appears; press Enter
4. Press Stop to exit Engineering mode and resume use of your treadmill
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Xterra TR600 TREADMILL wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info