Bedienungsanleitung XtremeMac Luna (Seite 8 von 13) (Englisch)

496940

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

LUNA™ User Manual

4. The minute section will then blink to indicate it can be adjusted. Turn the

Right Control Knob to change the minutes and push to accept and save

your changes.

5. Once you set the alarm time(s), you need to make sure to activate the

alarm(s). Push the Alarm 1 Button on the back left to activate Alarm 1

and/or push the Alarm 2 Button on the back right to activate Alarm 2.

The display will show each alarm time and source icon when the alarm is

activated.

SHORTCUT

You may also access Alarm 1 and Alarm 2 menus by

holding down the corresponding Alarm Button.

Setting Alarm Source:

1. Push the Right Control Knob to access the main menu. The menu will

appear on Luna’s display.

2. Turn the Right Control Knob to highlight either “Alarm 1” or “Alarm 2”

and push to select.

3. Turn the Right Control Knob until the “Wake To” menu item is highlighted

and push to select. Turn the Right Control Knob to choose between

“iPod”, “Radio”, or “Sounds”. Highlight your source choice and push to

accept.

Waking to iPod

– If “iPod” is selected as alarm source, be sure to properly dock your

iPod in the Universal dock well. If you do not dock your iPod, the

alarm source will default to the buzzer to make sure that you do

not miss your set alarm time.

– Set your iPod to shufﬂe or pick the song or playlist you would like

to wake to.

Note: Ensure your playlist has an adequate amount of songs to play for

the amount of time it will take you to wake.

Waking to radio

– If “Radio” is selected as alarm source, make sure the FM and AM

antennas are connected per the instructions.

– Next, you may select a preset station or tune Luna to your

preferred AM or FM station (see “Set Presets” on pages 16-17).

– To select a preset station, select radio as alarm source (see step 2

above). Push the Right Control Knob to select the “Presets” menu

item and push to select. The band and station will blink. Turn the

Right Control Knob to toggle through your preset stations. Push to

select desired preset station.

– To manually tune the radio, turn the Right Control Knob until

the “Tune” menu item is highlighted. Push to select. The AM/FM

band will blink to indicate that it can be adjusted. Turn the Right

Control Knob to the desired band and push to accept the band

and advance to tune the frequency. The frequency will then blink

to indicate it can be adjusted. Turn the Right Control Knob to tune

the desired frequency and push to accept.

Note: For best FM reception, the antenna should be extended fully and

vertically above Luna. For best AM reception, the AM loop antenna

should be positioned away from Luna.

Waking to Sounds

– If “Sounds” is selected as alarm source, you may select from

“Beeping”, “Buzzing” or “Ringing.” Turn the Right Control Knob to

the desired sound and push to select. The selected item will turn

from “OFF” to “ON” in the menu.

Setting Alarm Snooze Time:

1. Push the Right Control Knob to access the main menu. The menu will

appear on Luna’s display.

2. Turn the knob to highlight either “Alarm 1” or “Alarm 2” and push to

select.

3. Turn the Right Control Knob until the “Snooze” menu item is highlighted

and push to select. The snooze time will blink to indicate that it can be

adjusted. Turn the Right Control Knob to increase/decrease the snooze

time (from 1 to 60 minutes) and push to accept and save your changes.

Setting Alarm Volume:

Setting Volume Level

Luna allows you select a speciﬁc volume for each alarm, independent

of the last listening volume. This means you can go to sleep with

the volume barely on and still wake to a volume that is considerably

louder or vice versa.

1. Push the Right Control Knob to access the main menu. The menu

will appear on Luna’s display.

2. Turn the Right Control Knob to highlight either “Alarm 1” or “Alarm

2” and push to select.

3. Turn the Right Control Knob until the “Volume” menu item is

highlighted and push to select.

4. To select the volume level, push the Right Control Knob again. The

volume level will blink to indicate that it can be adjusted. Turn the

Right Control Knob to the desired volume level (from 5 to 20) and

push to accept and save your changes. The alarm volume cannot

be set lower than level 5 to ensure minimum waking volume.

Setting Volume Ramping

Luna volume ramping feature gradually increases the alarm volume

over a speciﬁed time period, from 0 to 60 seconds.

1. Push the Right Control Knob to access the main menu. The menu

will appear on Luna’s display.

2. Turn the Right Control Knob to highlight either “Alarm 1” or “Alarm

2” and push to select.

3. Turn the Right Control Knob until the “Volume” menu item is

highlighted and push to select.

4. Turn the Right Control Knob until the “Ramp Time” item is

highlighted and push to select. The ramp time will blink to indicate

that it can be adjusted. Turn the Right Control Knob to increase/

decrease the volume ramp time (from 0 to 60 seconds) and push

to accept and save your changes.

Setting Dimmer:

The brightness of Luna’s multifunction display can be speciﬁed for each

alarm. This means that you can fall asleep with the display dimmed and

wake to a brighter display.

1. Push the Right Control Knob to access the main menu. The menu will

appear on Luna’s display.

2. Turn the Right Control Knob to highlight either “Alarm 1” or “Alarm 2”

and push to select.

3. Turn the Right Control Knob until the “Dimmer” menu item is highlighted

and push to select. The dimmer level will blink to indicate that it can be

adjusted. Turn the knob to increase/decrease the dimmer level (from 0 to

20) and push to accept and save your changes.

XtremeMac Luna Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info