674720
38
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
36
Setting to connect the repeater controller S-COM7330
Set up instructions to interface the Triple Repeater Controller S-COM7330 with the DR-1X.
Modification of S-COM7330
1 Remove the 6 screws from each side and 2 screws from the top
cover of the S-COM7330, then remove the top cover.
2 Change Jumper pin J10C or J11C or J3C and adjust the semi fixed.
AF volume gain up for RX1 or RX2 or RX3.
3 Command Settings.
Select Path Access Mode: Carrier and CTCSS
Select COR Filter Delay: 300 msec
Select Dropout Delay: 0 sec
Setting of DR-1X
Set the DR-1X as follows.
Setting the communication mode RX: AUTO (AMS)
TX: FM (FIX)
Setting the tone signals: RX-TONE (100 Hz) (see page 25 and 27)
Connection with S-COM7330 and DR-1X
DR-1X S-COM7330 Connection
pin 1 EXT I/O pin 1 RX Audio Connect to DR-1X AF out
pin 2 EXT PTT pin 2 RX COR Connect to DR-1X SQL DET
pin 3
CTCSS/DCS DET
pin 3 CTCSS in Connect to DR-1X CTCSS/DCS decode output
pin 4 SQL DET pin 4 TX PTT Connect to DR-1X EXT PTT
pin 5 GND pin 5 TX Audio Connect to DR-1X AF in
pin 6 TONE IN pin 6 GND DR-1X GND
pin 7 AF IN pin 7 GND DR-1X GND
pin 8 DISC OUT pin 8 TX pin 8 Select TX LOGIC or TX CTCSS by JP pin
pin 9 AF OUT pin 9 GND DR-1X GND
pin 10 GND
I/O Controller
pin 1 to 6
Logic output
Connect to DR-1X EXT I/O
(needs S-COM programming)
pin 11 EXT PORT1
I/O Controller
pin 1 to 6
Logic output
Connect to DR-1X EXT PORT1
(needs S-COM programming)
pin 12 EXT PORT2
I/O Controller
pin 1 to 6
Logic output
Connect to DR-1X EXT PORT2
(needs S-COM programming)
pin 13 EXT PORT3
I/O Controller
pin 1 to 6
Logic output
Connect to DR-1X EXT PORT3
(needs S-COM programming)
pin 14 EXT PORT4
I/O Controller
pin 1 to 6
Logic output
Connect to DR-1X EXT PORT4
(needs S-COM programming)
pin 15 VCC OUT DC jack DC in Connect to DR-1X VCC out
The wiring paths shown by the dotted lines require programming the S-COM7330.
pin 1 EXT I/O Jumper to pin 2 EXT PTT or connect to S-COM7330 LOGIC OUT (L: EXT I/O enable)
pin 2 EXT PTT EXT PTT input from S-COM7330. It will be controlled by RX COR normally.
pin 3
CTCSS/DCS DET
Signaling decode output (CTCSS/DCS etc)
pin 4 SQL DET Noise SQL decode output (Connect to RX COR)
pin 5 GND GND
pin 6 TONE IN Tone input from S-COM7330 (Connect to TX pin8)
pin 7 AF IN Modulation input from S-COM7330
pin 8 DISC OUT RX audio output without de-emphasis
pin 9 AF OUT RX audio output with de-emphasis
pin 10 GND GND
38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu DR-1X-FR wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info