Bedienungsanleitung Yaesu FT-2000D (Seite 11 von 140) (Englisch)

478497

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Page 9FT-2000D OPERATING MANUAL

INSTALLATION AND INTERCONNECTIONS

GROUNDING

The FT-2000D transceiver, like any other HF communications apparatus, requires an effective ground system for maxi-

mum electrical safety and best communications effectiveness. A good ground system can contribute to station efficiency in

a number of ways:

 It can minimize the possibility of electrical shock to the operator.

 It can minimize RF currents flowing on the shield of the coaxial cable and the chassis of the transceiver; such currents

may lead to radiation which can cause interference to home entertainment devices or laboratory test equipment.

 It can minimize the possibility of erratic transceiver/accessory operation caused by RF feedback and/or improper cur-

rent flow through logic devices.

An effective earth ground system may take several forms; for a more complete discussion, see an appropriate RF engineer-

ing text. The information below is intended only as a guideline.

Typically, the ground connection consists of one or more copper-clad steel rods, driven into the ground. If multiple ground

rods are used, they should be positioned in a “V” configuration, and bonded together at the apex of the “V” which is nearest

the station location. Use a heavy, braided cable (such as the discarded shield from type RG-213 coaxial cable) and strong

cable clamps to secure the braided cable(s) to the ground rods. Be sure to weatherproof the connections to ensure many

years of reliable service. Use the same type of heavy, braided cable for the connections to the station ground bus (described

below).

Inside the station, a common ground bus consisting of a copper pipe of at least 25 mm (1”) diameter should be used. An

alternative station ground bus may consist of a wide copper plate (single-sided circuit board material is ideal) secured to the

bottom of the operating desk. Grounding connections from individual devices such as transceivers, power supplies, and

data communications devices (TNCs, etc.) should be made directly to the ground bus using a heavy, braided cable.

Do not make ground connections from one electrical device to another, and thence to the ground bus. This so-called “Daisy-

Chain” grounding technique may nullify any attempt at effective radio frequency grounding. See the drawing below for

examples of proper grounding techniques.

Inspect the ground system - inside the station as well as outside - on a regular basis so as to ensure maximum performance

and safety.

Besides following the above guidelines carefully, note that household or industrial gas lines must never be used in an

attempt to establish an electrical ground. Cold water pipes may, in some instances, help in the grounding effort, but gas lines

represent a significant explosion hazard, and must never be used.

PROPER GROUND CONNECTION

Linear

Amplifier

TNC

Transceiver

"Daisy Chain"

Linear

Amplifier

TNC

Transceiver

IMPROPER GROUND CONNECTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-2000D Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info