Bedienungsanleitung Yaesu FT-2000D (Seite 121 von 140) (Englisch)

478497

121

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Page 119FT-2000D OPERATING MANUAL

034 GEnE TRACK

Function: Sets the VFO Tracking feature.

Available Values: OFF / bAND / FrEq

Default Setting: OFF

OFF: Disables the VFO Tracking feature.

bAND: When you change bands on the Main (VFO-

A) side, the Sub (VFO-B) band’s VFO will

automatically change to be the same as that of

VFO-A.

FrEq: This function is the almost same as “bAND,”

however, furthermore, the Sub band’s (VFO-

B) frequency changes together with the Main

Band’s (VFO-A) frequency when turning the

Main Dial Tuning knob.

035 GEnE TX TOT

Function: Sets the Time-Out Timer countdown time.

Available Values: OFF / 3 / 5 / 10 / 15 / 20 / 30 min

Default Setting: OFF

The Time-Out Timer shuts off the transmitter after con-

tinuous transmission of the programmed time.

036 GEnE TRV SET

Function: Sets the 10’s and 1’s of the MHz digits display

for operation with a transverter.

Available Values: 30 ~ 49 MHz

Default Setting: 44 MHz

The default setting would be used with a 144 MHz

transverter. If you connect a 430 MHz transverter to the

radio, set this menu to “30” (the “100 MHz” digits are

hidden on this radio).

037 GEnE μT DIAL

Function: Selects the μ-TUNE mode.

Available Values: StP1 / StP2 / OFF

Default Setting: StP1

StP1: Activates the μ-TUNE system using

“COARSE” steps of the

[

VRF

]

knob (2 steps/

click) on the 7 MHz and lower amateur bands.

On the 10/14 MHz bands, “FINE”

[

VRF

]

knob

steps (1 step/click) will be used.

StP2: Activates the μ-TUNE system using “FINE”

steps of the

[

VRF

]

knob (1 step/click) on the

14 MHz and lower amateur bands on the Main

band (VFO-A).

OFF: Disables the μ-TUNE system. Activates the

VRF feature on the 14 MHz and lower amateur

bands on the main band (VFO-A).

ADVICE:

If the optional RF μTuning Kit is not connected, this ad-

justment has no effect.

038 GEnE SNB LVL

Function: Adjusts the Sub band (VFO-B) receiver’s IF

Noise Blanker level, when the Noise Blanker is engaged.

Available Values: nAin(MAIN) / 0~100

Default Setting: nAin(MAIN)

When this menu is set to “nAin(MAIN),” you may adjust

the Noise Blanker level using the front panel’s

[

]

knob.

039 GEnE SUB FIL

Function: Defines the Sub band (VFO-B) receiver’s CW

narrow filter.

Available Values: 1200 / 500 / 300 Hz

Default Setting: 1200 Hz

ADVICE:

This Menu item tells the microprocessor which (if any)

optional filter has been installed.

040 GEnE MIC SCN

Function: Enables/disables scanning access via the

microphone’s

[

]

[

DWN

]

keys.

Available Values: On / OFF

Default Setting: On

041 GEnE SCN RSM

Function: Selects the Scan Resume mode.

Available Values: CAr / 5SEc

Default Setting: 5SEc

CAr: The scanner will hold until the signal disappears,

then will resume after one second.

5SEc: The scanner will hold for five seconds, then re-

sume whether or not the other station is still

transmitting.

042 GEnE ANTIVOX

Function: Adjusts the Anti-VOX Trip Gain which is the

level of negative feedback of receiver audio to the micro-

phone, to prevent receiver audio from activating the trans-

mitter (via the microphone) during VOX operation.

Available Values: 0 ~ 100

Default Setting: 50

043 GEnE FRQ ADJ

Function: Adjusts the reference oscillator.

Available Values: –25 ~ 0 ~ +25

Default Setting: 0

Connect a 50-Ohm dummy load and frequency counter to

the antenna jack; adjust the

[

SUB VFO-B

]

knob so that

the frequency counter reading is same as the VFO fre-

quency while pressing the PTT switch.

ADVICE:

Do not perform this Menu item unless you have a high-

performance frequency counter. Perform this Menu item

after aging the transceiver and frequency counter suffi-

ciently (at least 30 minutes).

MENU MODE

GENERAL GROUP

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-2000D Seite 121

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info