Bedienungsanleitung Yaesu FT-2000D (Seite 126 von 140) (Englisch)

478497

126

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Page 124 FT-2000D OPERATING MANUAL

MODE-SSB GROUP

084 J3E MIC SEL

Function: Selects the microphone to be used on the SSB

modes (LSB and USB).

Available Values: Frnt / dAtA / PC

Default Setting: Frnt

Frnt (FRONT): Selects the microphone connected to

the front panel’s MIC jack while using

the SSB modes.

dAtA: Selects the microphone connected to

pin 1 of the PACKET Jack while us-

ing the SSB modes.

PC: This parameter is for future expansion

of this transceiver’s capabilities, but at

this time is not supported.

085 J3E TX BPF

Function: Selects the audio passband of the DSP modula-

tor on the SSB mode.

Available Values: 1-30 / 1-29 / 2-28 / 3-27 / 4-26 / 3000

1-30: 50-3000(Hz)

1-29: 100-2900(Hz)

2-28: 200-2800(Hz)

3-27: 300-2700(Hz)

4-26: 400-2600(Hz)

3000: 3000WB

Default Setting: 3-27 (300-2700 Hz)

NOTE:

The apparent power output, when using the widest band-

widths, may seem lower. This is normal, and it occurs be-

cause the available transmitter power is distributed over a

wider bandwidth. The greatest compression of power out-

put, conversely, occurs when using the “4-26” setting (400-

2600 Hz), and this setting is highly recommended for con-

test or DX pile-up work.

086 J3E LSB CAR

Function: Adjusts the receiver carrier point for the Main

band’s (VFO-A) LSB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz/steps)

Default Setting: 0 Hz

087 J3E USB CAR

Function: Adjusts the receiver carrier point for Main

band’s (VFO-A) USB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz/step)

Default Setting: 0 Hz

088 J3E SLSB CR

Function: Adjusts the receiver carrier point for the Sub

band’s (VFO-B) LSB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz/step)

Default Setting: 0 Hz

089 J3E SUSB CR

Function: Adjusts the receiver carrier point for Sub band’s

(VFO-B) USB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz/step)

Default Setting: 0 Hz

RX AUDIO GROUP

090 rout AGC SLP

Function: Selects the gain curve of the AGC amplifier.

Available Values: nor / SLP

Default Setting: nor

nor (NORMAL): The AGC output level will follow a

linear response to the antenna input

level, while AGC is activated.

SLP (SLOPED): The AGC output level will increase

at 1/10 the rate of the antenna input

level, while AGC is activated.

MENU MODE

NORMAL

Input Signal

utput

SLOPE

091 rout HEADPHN

Function: Selects one of three audio mixing modes when

using headphones during Dual Receive operation.

Available Values: SEP / Con1 / Con2

Default Setting: SEP

SEP (SEPARATE): Audio from the Main (VFO-A)

receiver is heard only in the left

ear, and Sub (VFO-B) receiver

audio solely in the right ear.

Con1 (COMBINE 1): Audio from both Main (VFO-

A) and Sub (VFO-B) receivers

can be heard in both ears, but

Sub (VFO-B) audio is attenu-

ated in the left ear and Main

(VFO-A) audio is attenuated in

the right ear.

Con2 (COMBINE 2): Audio from both Main (VFO-

A) and Sub (VFO-B) receivers

is combined and heard equally

in both ears.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-2000D Seite 126

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info